Jump to content
SAU Community

Recommended Posts

anyway i changed my plugs again then i took it for a drive everything was perfect, until the next morning driving to work i give a little bit and a notice a small misfire.

i go for a drive at lunch time its a pig again idels shit aswell,

can someone please help and yes iv searched

Link to comment
https://www.sau.com.au/forums/topic/152448-r32-gtr-misfire/#findComment-2846481
Share on other sites

never try to regap iridiums they are set at either 0.8 or 1.0 for a reason if you wanna run a smaller gap use ngk or bosh cheapies

and a 0.7 gapis prolly the reason you are getting the missfire

i run ngk @1.0 mm and never have a problem

Link to comment
https://www.sau.com.au/forums/topic/152448-r32-gtr-misfire/#findComment-2846865
Share on other sites

but thats the thing race pace gaped my periously irudiums to .7

and now this my second set off the plugs this week iv got platinum's now,

but what i dont under stand is why is mis firing same plugs same gap,

this is really pissing me off

Link to comment
https://www.sau.com.au/forums/topic/152448-r32-gtr-misfire/#findComment-2846902
Share on other sites

thhis really starting to piss me off, i just tryed the copper plugs aswell, 1st i gapped them 2 .8 was a lot better but still had a miss above 7000rpm, then i gapped them to .7 was fine for the first drive to the car wash, i washed my car driving home from car wash missing like a bitch again,

i wanted to fix this b4 the cruise tomorrow, please help someone

Link to comment
https://www.sau.com.au/forums/topic/152448-r32-gtr-misfire/#findComment-2850679
Share on other sites

perviously as stated iv gapped them b4 with no problems just un plug my coils one at a time and the idle change on every one, so its not the coils

that doesnt eliminate the coils at all...

only if the miss is at idle...which its not.

try a new set of coils dude, swap with a mate or something, cheaper than going to a shop,

Link to comment
https://www.sau.com.au/forums/topic/152448-r32-gtr-misfire/#findComment-2856808
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...