Jump to content
SAU Community

Recommended Posts

Hey guys,

Have had trouble starting my car only sometimes lately. Today it took me about 10 turns of the switch to get the starter motor to turn over the engne.

I get in the car, put the key in, turn it past accessories to the 'ON' position I guess, let the fuel pump go for about 5 seconds before turning the key to 'START' and nothing.... just cuts out the radio. Tried it about 7 times, then took the key out, turned it around, did the same thing, did the same thing first attempt, and then on 2nd attempt fired straight away.

Has this happened to anyone else? And what could be the causes?

Worn out ingition barrel not contacting anymore (I have no idea how it works inside the barrel)?

Starter motor contacts bad??

It used to only do it maybe once or twice at most, and only usually every 5 or so times of starting the car (it would usually strart straight away), but yesterday afternoon and today afternoon I had trouble.

Any other ideas?

Thanks,

Fixxxer

Link to comment
https://www.sau.com.au/forums/topic/153238-starting-problems/
Share on other sites

If the key goes in and turns to start normally the first time before flipping it then its got nothing to do with the key or barrel. However commodores use an anti theft device in the key head that flipping the key sometimes helps, but thank god you dont have a commonwhore!

Most likely a starter problem. To be safe you should get a multi meter and load test the battery. First unplug the ignitor so the car wont start. Attached the two terminals of the multimeter to the battery terminals then get someone to try cranking the engine and while its winding over watch the reading on the multimeter. If it drops below 10 volts then your battery is dieing. If not and it stays around 11-12 volts the battery should be fine and you can be more sure its the starter/solinoid causing the fault.

Battery should be fine, its a good battery, I replaced it only about 3 months ago....

It's not like the starter is struggling to start the car, it's like the power is not getting to the starter, and then suddenly i turn the key the right way or something and it fires instantly.

Fixxxer

OK then we can rule out the battery, good. Next look at the starter & solinoid (which are combined) and earthing of the circuit. If there isnt a good earth (strap) you may aswell be not supplying enough power as its the same end result.

Deren

I had the very same problem on my car some time ago!

It ended up beeing the front + and -poles on the left side of the engine bay.

The thing was that the prior owner had connected front-lights to the +pole and that created a gap big enough for dirt getting in and ruin the connection.

Apperently the connection was good enough for panellights and such, but not good enough for the starter.

If i recall correctly i think the windows wouldnt move either...

Hope that helps!

As the brushes wear in a starter you will get an inconsistent starting patterns. But I have also seen a brand new battery off the shelf that I have had to fit to a customers car and it has had a brake in between the cells.

Do what Deren said by checking battery voltage, whilst cranking - this will give you the best indication, also check you main battery lead going to the starter - if these look ok - its time to pull the starter out, and give it to some mug they call an auto electrician :P.

Cheers

Sumo

Ok I will look around the starter motor and see if there is anything wrong with connections.

Next I'll check the battery and connections to the battery, but like I said this doesn't seem to be a problem as there is plenty of kick to start the car when the starter works, and this has been a problem ever since I got the car a year and a half ago (with a different battery).

Fixxxer

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi There I went through a rabbit hole of reading about Xenon headlights and the ADR regulations for having them installed. As people have been defected by running factory xenon I was researching in ways to make them compliant. Everyone always say needs to be self leveling and have washer installed, which I don't necessarily agree with. For this argument I'm using R34 as reference as I'm more aware on the construction of the headlight compared to the R33 Xenon, which may still be the exact same case.   For the self leveling clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles As you can see the bold text "these manually adjustable devices from driver seats" are fine to use. As Series 1 Xenon model headlights do have a 4 level adjuster on the right near the ignition (however not series 2) then these model are consider compliant in that argument.   For the Self Cleaning aspect of this argument clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles Now i can understand the argument that Xenon will need a washer as they are over 2000 lumens, but I clicked on the 12 at the end of that sentence and it takes me to the end notes which states R34 for headlight lenses are plastic, not sure if PL is mark as I don't currently have my skyline to confirm that marking is there. But could you not technically get a lenses with the PL marking on it and then get away with the argument that you need a washer. I went through a quick read of the adr and might have missed something else that may cause them to be non-complaint.    But wouldn't these technically be complaint headlights   Would love to hear other people input on this and shed some light   Edit In regard to the the washer portion I might be mistaken ADR 45 (which I believe is Regulation NO.45) states 12 cd (candela) I dont understand that portion in regarding to calculating the candela if anyone can shed some light. Otherwise I guess throw in a washer for the headlight and you definitely comply.
    • Took it to all Japan day, flogged the hell out of it and took it all, am a very very happy man  don’t know how that ended up in Greg’s thread before
    • Hey Nismo, any chance in the world you still have these seats?
    • I'd say closer to OG GTX3582R, just smaller trim - so 59mm inducer/82mm exducer as opposed to 62/82 for the first gen GTX3582R. Yeah EFRs were boss, the EFR8474 is still an absolute beast and it perplexes me that people still go to things like Turbosmart/Garrett etc when the results people are getting with those are pretty unremarkable compared to what you could get with a turbo available well before those options came out.  DriftSquid (I think) "upgraded" from an EFR9174 to a Turbosmart turbo and promised a comparison video - and kinda shuffled awkwardly and did a bit of diversion from the fact that they didn't get any improvement going to the currently massively hyped brand of turbo from a turbo that was a bit of a frankenstein that had been well superceded in it's own range before the Turbosmart unit he put on there even came out. I suspect the EFR would outperform most Xonas for what a lot of less-insane RB owners would go for, in the 400-600kw range but the Xonas are looking hard to beat up to maybe in the mid 700kw range at this stage- basically where EFRs don't really reach, and before the Precision turbos take over.  What the Xonas do well in the "EFR range" is be easier to package etc, and work very well if a divided housing doesn't suit your application.  
    • Are you sure the gasket is blown? What are the issues? Thermocure is the only flush I've seen do anything with rust, very impressed with that, Prestone, rust will be by the pool having a cigarette.  
×
×
  • Create New...