Jump to content
SAU Community

Recommended Posts

Has anyone installed 6" component speakers in a R34, i am currently doing my whole new system and decided to put the components in the back as there is no room up the front for all the parts, does anyone have pics of work they have done or had done?

Also nissan have made a damn good car except the fact that i haven't stopped swearing since i started this project cause nothing lines up with the stock system.

-----------------remember smoke tyres not drugs-----------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/
Share on other sites

just took the whole rear parcel shelf out so could get to speakers then found that the plastic cover over speakers has srews holding them on which you can access through some holes through the boot below the shelf, would of been handy to be able to see them first up, the shelf just clips through to the boot and also under the overlap behind rear seats, also to get my clarions in had to drill out the existing holes to fit new configuration.

i mean really it's not that hard if ya think about it hoo hah ( except for all the swearing)

----------------remember smoke tyres not drugs--------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855693
Share on other sites

directly underneath the speakers in the boot there should be a lot of holes in the sheetmetal i'm not sure what ones but there should be four on each side that go th the screws, really hard to see that's why i pulled the whole parcel shelf out it's much easier, there should be two blue clips in the boot and three inside the car behind the rear headrest plus you have to take the 3 bolts out that are for the baby harness points to get the shelf out. hope that helps

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855770
Share on other sites

there are two bolts holding the bottom part of the seat, remove tht. Then just take out the bottom piece seat and the rear there are two bolts as well at both sides, undo those, then lift the back piece as it is hooked on to the frame behind..quite a hassle because they don't fold down :cheers:

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855971
Share on other sites

nice work r34-gtt not that hard once you get it off and see whats going on under there. have my speakers in as well and just fitted the components box and tweeters to the back shelf as well so i'll post pics when it's all back together.

-------------------remember smoke tyres not drugs---------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2856781
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...