Jump to content
SAU Community

Rb30 Clutchfan

CeJay

By CeJay,
in General Maintenance

 Share

Recommended Posts

CeJay Grand Master

CeJay

Posted
Posted

Havent noticed much on this in this section, so would just like to clear up, i've been told the rb30 clutchfan will bolt straight up if you have an rb25/20, has anyone done this? Have they had any probs? As the charge for an rb30 clutchfan is very much more attractive than nissan new for a rb25 one.

thx

chris

Link to comment
https://www.sau.com.au/forums/topic/153851-rb30-clutchfan/
Share on other sites
BH_SLO32 Proficient

BH_SLO32

Posted
Posted
Havent noticed much on this in this section, so would just like to clear up, i've been told the rb30 clutchfan will bolt straight up if you have an rb25/20, has anyone done this? Have they had any probs? As the charge for an rb30 clutchfan is very much more attractive than nissan new for a rb25 one.

thx

chris

Yes, I recently replaced the clutch fan on my RB30 (R31 skyline) with one of a few spare Rb20 and Rb25 fans in my shed.

If you want one I can sell you one for $30 + postage. I should have a good one in the shed.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/153851-rb30-clutchfan/#findComment-2862503
Share on other sites
Bl4cK32 Grand Master

Bl4cK32

Posted
Posted (edited)

Are u talking about the fan itself or the clutch it sits on?

the fan - they all bolt up the same, but it has been said the rb25 fan is better designed (pulls more air?)

with the clutch - the only one that is a direct replacement is the rb30et one.

It is the same as the rb20/25det clutch.

Rb30e clutch shaft that bolts to the water pump is longer and thinner from memory...not much, but enough to not warrant using it...

Edited by Bl4cK32
Link to comment
https://www.sau.com.au/forums/topic/153851-rb30-clutchfan/#findComment-2881413
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...