Jump to content
SAU Community

Recommended Posts

the whiteline front camber kit is like $160 if you get it via the whiteline online store..come to think of it.. repco / autobarn have it at that price also.... i dunno why there $300 in the GB?? maybe you get 2 sets or something??

kca348 is wat ur after i think

Thanks justin.

I'm not sure if I need 1 kit or 2.

Do you only use one in the inner side if your alignment isn't that bad? (i.e. only need 1 pack)

Cheers.

I'm wondering if you just put it on one of the 2 points where it meets the chassis (in where one of the wishbone bushed was). This would change camber and toe at the same time.. so then you just get it aligned and they adjust tie rod aswell to make sure the toe is right??

Any comments appreciated

Anybody got the fitting instructions? Its not on the web..

Edited by benl1981

cause at the moment on my last allignment it was like 1.39(not sure if theres meant to be a minus in there!) or something

what does that mean? :laugh:

he said thats the most negative he could get out of the stock arms/camber

evil, your alignment guy was pulling your middle leg.

There is no camber adjustment stock on the front of skylines.

That number is most likely -. If it's plus, there's something seriously wrong with your car.

The front camber kit will allow you to run more neg camber for the track, as well as it will allow you to dial out neg camber from lowering the car for the street for tyre life

if its for an R33 then $300 is a complete rip off. I don't know why it was priced anywhere near that in the group buy (maybe because the R32 kit is apparently that much, maybe they just dragged the same price over for the 33)

I don't think I even paid half of that ridiculous price...i've got the full whiteline/bilstein kit now, and I only got the springs/shocks and bump stops/dust covers from the GB...the rest of it I got from repco way cheaper, and thats without any bartering at all...I just gave them part numbers and the first prices they gave me for each item were cheaper

Shop around people...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...