Jump to content
SAU Community

Recommended Posts

Hi Guys,

For Sale:

1989 Black R32 GTST type M Coupe

Full GTR Bodykit

Gtr Aluminium Bonnet and Bootlid

16" black Watanabe rims

Ganador Style Mirrors

Engine:

Rb20det Silvertop

Garrett T-04 Turbo

HKS External Wastegate

3" Turbo back exhaust

Hi Flow Cat

2 extra injectors in manifold controlled by Greddy Rebic fuel computer (in cabin)

Brake Booster Stopper

Front Mount Intercooler

Hybrid Electronic Boost Controller (with Overboost 10%)

GTR Fuel Pump

K&N Filter Panel in Std Airbox (Also have K&N Pod with all adapters)

re mapped ECU tuned in Japan.

Suspension & Transmission

Exedy Heavy Duty 5 puck Clutch (new)

Nismo Upgraded Clutch Plate (new)

Short Shifter

Tein Superstreet Coilovers all around (Damper and Height Adj)

Front Mines Strut Brace

2 way LSD

Interior

HKS 3 gauge cluster (Boost, Water and exhaust temp)

Greddy Full auto turbo timer

Nardi Steering wheel

Razo Gear knob

JVC MP3 headunit

2 x 12" clarion subs

Clarion Splits and rear speakers

Amp

Car has done 120,000km I've had the car for 6 months and am selling due to company car. Always serviced and very clean. Interior is immaculate. Has genuine Skyline Floor mats, Brand new windscreen and seats are in very good condition (no rips). Very regretful sale.

Looking for $14,500 with RWC or $13,500 without flexible with price but not by much. Please serious buyers only plus I have all original parts (shifter, steering wheel, airbox)

Reg till end Sept 07

Contact Dennis on 0413 587 347 anytime or email [email protected]

post-32632-1170667197.jpg

post-32632-1170748929.jpg

post-32632-1170748965.jpg

post-32632-1170748988.jpg

Edited by Initialdennis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...