Jump to content
SAU Community

Recommended Posts

  • Replies 122
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Stop ripping me off Grant! Hahaha!

Nice kit!

post-8679-1172620328.jpg

That kit will bring you lower than the Dayz kit too I think, even if it is just visual and not actual as the side skirts (steps) are a lot squarer.

Cheers

Luke

hey on the skirts, do they sit liek the factory ones or do they slide in between the door like most kits?

Not sure how the factory skirts fit, mine do sit on the sill panel and run under the doors.

(thanks Alex, black car, wash - then photograph before the dust settles)

i still dont like hte height

If i want to go lower, i need to get shorter springs (think 120mm length stupid short) and helper springs.

i have a custom coilover in the works from a guy around here. im trying to get a decent price from him and not some stupid 2,000 dollar price tag.

ok, started fabbing up the exhaust today

i have all the piping from the cat to the sway bar done. i have to pick up some more 3 inch pieces and pie cut and weld them to make the s shape right there.

my aero will be here friday

my gauges should be nere in a week and a half

ORdered a greddy oil filter relocation kit

Ordering NRG Fuel pressure regulator nad AEM UEGO monday

ordering cusco r33 GTR sway bars monday

and hopefully have my wheels sold so i can get some 9s in the rear so i can go uber low.

Where the hell are you gonna relocate your oil filter to, Grant? I can't find anywhere decent to put one without it then being in the way of something else! Most people with Skylines, etc. put them on the front of the driver's side strut tower, but the Stagea has a massive fuse box there, so that kinda rules that out...

pics

fo sho they fit great now!

can you take some closer pics to show what it looks like up close.. and i forgot what else i was going to say :rofl:

nice car anyways :( coming along good. wich i had millions of dollars spare like you

Where the hell are you gonna relocate your oil filter to, Grant? I can't find anywhere decent to put one without it then being in the way of something else! Most people with Skylines, etc. put them on the front of the driver's side strut tower, but the Stagea has a massive fuse box there, so that kinda rules that out...

:Shrug: it is the kit specifically for hte stagea. ill have to take a closer look at the instructions to find out where. but its not a universal kit, so it has to go somewhere

can you take some closer pics to show what it looks like up close.. and i forgot what else i was going to say :rofl:

nice car anyways :( coming along good. wich i had millions of dollars spare like you

what do you want more pics of?

when i get my kit i will sell you the skirts

So whats thie Dayz thing?

i saw the badge but i dunno what it means

thanks i have only just been able to log back on and finally came across this....thats excellent thanks champ..let me know when :wub: send us a pm on what price you would be after and freight to perth :no:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...