Jump to content
SAU Community

Recommended Posts

i have a series 2 r33 it has standard central locking with a button on the key and it works fine. i'm trying to wire an after market alarm system from jaycar but cant seem to figure out how to tap into the standard central locking does any body have any idea's? or know where i can get a wiring diagram any help would be much appreciated cheers brad

Link to comment
https://www.sau.com.au/forums/topic/155692-alarm-issues/
Share on other sites

there is A LOT that can go wrong doing what you are attempting.

would strongly suggest getting it done properly if you can't work it out.

nissan use two systems on those and the driver and passnger doors are separate.

Link to comment
https://www.sau.com.au/forums/topic/155692-alarm-issues/#findComment-2895829
Share on other sites

there is A LOT that can go wrong doing what you are attempting.

would strongly suggest getting it done properly if you can't work it out.

nissan use two systems on those and the driver and passnger doors are separate.

yeah im fairly sure they are nagativley tiggered. im just needed any ideas thats all

Link to comment
https://www.sau.com.au/forums/topic/155692-alarm-issues/#findComment-2895856
Share on other sites

i have a series 2 r33 it has standard central locking with a button on the key and it works fine. i'm trying to wire an after market alarm system from jaycar but cant seem to figure out how to tap into the standard central locking does any body have any idea's? or know where i can get a wiring diagram any help would be much appreciated cheers brad

There is an easy way to do this but will takr too long to explain by typing just call me the phone will be on all night

l

Leon 0407106822 :happy:

Link to comment
https://www.sau.com.au/forums/topic/155692-alarm-issues/#findComment-2896477
Share on other sites

There is an easy way to do this but will takr too long to explain by typing just call me the phone will be on all night

l

Leon 0407106822 :P

cheers i may do that i figured out that if i earth the purple wire and give the yellow +12 it locks and if i give the yellow wire an earth and the purple +12 it unlocks

Leon do you have msn

Link to comment
https://www.sau.com.au/forums/topic/155692-alarm-issues/#findComment-2896506
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...