Jump to content
SAU Community

Perfect Gift For The Special Person - Too good for the classifieds


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

I would be interested is hadnt JUST bought a pair of nail scissors! oh well, scissors are superior anyway due to their more accurate cutting of nails, and they hold their value better

I'm a newbie to these here forums and I'm interested in purchasing my first nail clipper.

Can you tell me how it handles compared to say, a nail file or just teeth?

What's its rear clip kw? What is the current condition of the lever?

Will you take a trade for two pegs and a telephone adapter?

Edited by Hell Fire
Where are my photos showing how low these clippers actually are???

Say in compairson to a LUX55

Along with this, have you not been able to dyno it at all? Say because it's so low you can't get it up over the slight incline?

HAHAHA! How does a newbie know about me not being able to get it up!!

gf-ninja.gifemot-iiam.gifgf-ninja.gif

Nah, I was there, I actually posted a little introduction post in whoretown, but like everything in whoretown it disappeared in the crap pretty quickly.

Edited by Hell Fire
gf-ninja.gifemot-iiam.gifgf-ninja.gif

Nah, I was there, I actually posted a little introduction post in whoretown, but like everything in whoretown it disappeared in the crap pretty quickly.

Welcome to whoretown.

We talk alot of crap

  • 1 month later...
Greetings, many questions,

Are clippers Series 1 or 2?

1.5 (please see previous posts)

(has a series 2 bottom end for better clipping power)

what oil do you use and how often do you service it?

do you have service logs???

1.5 (please see previous posts)

(has a series 2 bottom end for better clipping power)

what oil do you use and how often do you service it?

do you have service logs???

About as often as I serviced LXU55 (not often), logs are about as genuine as the LXU55 ones too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...