Jump to content
SAU Community

Recommended Posts

My bonet has etched mark on it, apparently was resprayed before I bought it. Also a few deep stone chips.

The body stripe also reveals that the left rear quarter panel may have been resprayed as well as the passenger doors.

Also a deep scratch 8cm long in the boot, not easy to touch up.

I also want to put in Type-M factory option front bumper + side skirts so it goes......

- $800 for fitting front bumper and side skirts and paint within this week...

- $1400 to repaint the bonnet + both front guards + extra $600 if I want the type-M bumper as well. Wait a month to get enough money for it.

- $3500 for full body respray. Wait 2 months to get enough money for it.

You guys reckon which one the best way to go ?

Link to comment
https://www.sau.com.au/forums/topic/15852-paintwork-3-choices/
Share on other sites

This quote is from a workshop I know that have high quality job. They did a panel respray on my previous car and I couldn't spot the repair, very professional. They are only 2 blocks away from where I live so that's a bonus point, I can just walk up there to pick up the car when it's finished.

If you know someone else in Melbourne who can do a top quality respray for much less than $3500, let me know. And I mean top quality, no dodgy cheap jobs.

hehehe...

who said my car is black????

my car is wine red, so even if I bought your bumper, I will need a $800 respray anyway.....

and I already have the bumper and side skirts already.

so I can't buy another one.

I will have a standard (non type M) bumper in burgundy for sale in a few weeks after I put on this type M bumper on.

well F#%k you for caring but i dont think it would cost to get a standard type m front bar sprayed and fitted for $600 if you bought my bar for $150 resprayed shouldnt cost you more than $100-$150 thats $300 but u know what you can get f%#cked cause i aint selling your poor arss nothing!

hmmmm seems that I've got three votes for $3500 full professional respray.

maybe that's the way to go to ensure that the paints are all uniform throughout the whole body... rather than a patch here and there? beside that body stripe looks a bit like the 80s anyway.

I have been around a few spray paint joints here in adelaide and asked for a cheap blow over that looks good.. Basically nothing fancy just nice and clean looking.

oh that will be $5000... WTF i asked for a cheap job....

I have had 3 quotes and all have been 5grand...

bit of tension felt in this thread

ease up guys!

i think save ur money for the full job. $3500 is a good price.

other wise you will end up paying more in the long run when you want to get other parts painted too.

Just a suggestion. If you are about to fit a m-spec front bar to your car, do what i have done to mine (attachment below), so that is you decide to get a fmic in the future you will have full air flow to it.

Take it to a plastic welder (i took mine to a bumper repair shop, in Airport West) tell him to cut the middle bar off (the one that supports the number plate) and use the off cuts to seal the remaining cut outs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...