Jump to content
SAU Community

Recommended Posts

Hey guys,

Im going to get my suspension fitted early next week - got the whiteline f & r sway bars and front castor adjuster - what sort of settings should I say to them? Ive got the bilstein shocks and white line springs package already fitted - need these new mods to work well, car is used mainly on street but with track days around once a month.

Any suggestions?

Cheers!!

Chris

I'd start with soft/soft on the sway bars and work from there. If it under steers, tighten the rear. If it over steers tighten the front.

If you have a gtst then I'd go for as much caster as you can get without the tyres scrubbing when you turn the wheel. I go even side to side with no ill effects on the street.

yep. ask for max castor they can get. as for bars, me personally would start with front to full soft and rear to 1 step up from soft. :D

rear is a piece of cake to get to, just jack up the back and you're away.

Front requires removal of the wheels to get at the links easily (atleast in a 32) and it can be a little awkward getting the link in and out of the bar.

As the baron has eluded to, you'll probably find the car under steers with both bars at soft initially and so you will be tightening the rear up.

tyres - true! :laugh:

On the street, they hold well as for 1. I hardly take the car out and 2. no point pushing it too hard!

However I'll most likely be using those federals 595RS's which has been posted in this forum section!

Thanks again :)

Chris

done and done :(

Car feels fantastic!

They put the fronts on medium and rears on hard

and max castor

had to go through Galston Gorge (NSW people would know this road!) the other day - car never felt so alive!

Still going to take a bit of getting used to - as I did find, got on the gas a wee bit early and the rear stepped out - but that was silly anyway :ninja:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...