Jump to content
SAU Community

Recommended Posts

I have now been tuning ECU’s for about 2 years and have had excellent results. I have tuned everything from completely stock cars to highly modified with larger injectors, turbos, AFM and even methanol injection. I have currently have the equipment to tune R32, Cefiro, Silvia, 180SX, Laurel, 300ZX and a few others. I can not tune R33 skylines due to the chip used.

I have all the equipment and have the ability to do map tracing and socketing ecu’s. All you have to do is pay for the dyno time and a bit to cover my costs.

You would have to allow for 2 hours dyno time and $50 for my efforts and cost of chips, sockets, travel, and time. Normally people would charge a minimum of $350 for this service.

You will get a new fuel and timing map to suit your mods, speed limiter and rev limit set to whatever you want, mass AFM sensing will be removed so no more “boost cut” and all will be checked on the dyno. You will have better power delivery and in most cases improved economy and heaps more power.

What I will want in return is a before and after printout of the dyno runs to show the performance gain achieved. Mainly so I can have some testimony from customers. That’s all I ask

Below is a couple of graphs of cars tuned by me.

100_1189.jpg

R32 skyline RB20DET Slide hiflow, Stock injectors, RB20AFM, GTR fuel pump 14psi.

dyth.jpg

R32 skyline RB20DET Slide hiflow, GTR injectors, RB20AFM, GTR pump 18psi.

If you are interested please PM me.

Thanks!

I am unable to do R33's due to the type of ROM they use. the chips are $100 each and you can only write to them once :0 so each retune needs a new chip. and I don't have a suitable programmer :)

With R32 skylines and other nissan ECU's they used an EPROM that can be erased and reused.

Cheers!

Hey Nic,

I will most likely be interested in this after I get my GTR changed to Canberra Rego, had abit of delay the last couple of weekends due to the rain. I think my car was running pretty rich hence the dirty bumper that you usually see when I drive the R32 to work.

Michael

hey mate can you remap s14 series 2 ? Also have much roughly when every thing is done ?

Hi Cambo. Yes it can be done but it gets expensive very quickly

With The S14 there are 2 different types of ECU. 1 can be tuned and the other not. You need to fit a daughter board with 2 eproms. the daughter board is $100 eproms a few $$$ and than tuning. all up including dyno time you would be looking at between$600 and that is if your ECU is the tunable one :ninja: if not you would have to hunt around for the correct ECU and would probably pay $200 for one. by that stage you are into Power FC territory.

Hey Nic,

I will most likely be interested in this after I get my GTR changed to Canberra Rego, had abit of delay the last couple of weekends due to the rain. I think my car was running pretty rich hence the dirty bumper that you usually see when I drive the R32 to work.

Michael

really? i'd just come to accept this was the price i paid for buying a white gtr. i may be interested in that case. so i'm assuming you can still work some magic with a completely stock 32gtr?

a completly stock GTR will benifit the most from a remap :) they run ultra rich from factory 10:1 at full throttle and also have a slightyl erratic timing map.

you can gain 30rwkw with just a remap and no other changes :D you will also have better fuel economy and less black crap!

My car is the one in the 2nd pick making 238rwkw (now a bit more) and i never get any buildup on my bumper. (it is black already) but if you wipe it no soot comes off:)

count me in then. just gimme a couple weeks for some funds to come in.

edit - having never chucked a car on a dyno before how much would i be looking at for dyno use and would there be an ideal dyno in canberra to use? cuz obviously i'd rather use an accurate one!

Edited by shredder667

well it looks like my turbo has finaly bit the dust. so im looking at getting it high flowed within the next 4-5 weeks. once thats done i'll finaly get you to tune mine.

no probs ;) happy to help.

checkout sliding performance turbos :D thats what have put on mine and 240rwkw later i am really happy with it. they cost around $1000 vs $2000 for a GCG hiflow

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...