Jump to content
SAU Community

14th April - So You Think You Have A Fast Car - Prove It! Win Cash And Trophies


Recommended Posts

Bring your car out to the next sprint event at Queensland Raceway and enter your car in the AMEC Automotive Performance track event, to be held in conjunction with the next QR sprint day.

There are 2 categories, the 3 fastest cars in each category win CASH and trophies!

the cash prize pool split will be as follows:

FOR CARS WITH UNDER 60s Personal Best (Category A):

1st place: 50% of category A prize pool

2nd place: 30%

3rd place: 20%

FOR CARS WITH OVER 60s Personal Best (Category B):

1st place: 50% of category B prize pool

2nd place: 30%

3rd place: 20%

there will also be a trophy for last place - the wooden spooner encouragement award :laugh:

ENTRY FEE: $25 in addition to your QR Sprint fee OR $20 for pre-entry.

HOW TO ENTER: entries will be taken on the day or you can pre-enter for a discounted entry fee of $20. after you have confirmed your sprints entry send me a PM if you want to enter our event.

YOU MUST ENTER THE QR SPRINTS SEPERATELY PRIOR TO THE TRACK DAY. The Entry form for the QR sprints is found here:

http://www.queenslandraceway.com.au/entry_...rints_entry.pdf

WHEN: the next QR sprints round on April 14th.

Of course our own car is not eligible to compete in the event! :)

see you on the race track!!

Might come out fer a run~It's only the sprint or sprint + clubman? Cost of entry for the day?

the event will only be run on the sprint circuit. entry for the QR sprints is $90. the additional entry fee for our event is $20 prepaid or $25 on the day. send me a PM to arrange a prepaid entry.

sounds like fun. We will be out there for the sprints. What times you run around there now AMEC?

last time we did a new PB of 57.5. since then we've put AP Racing 4 pot calipers on the rears :pirate: we're going down to the Nissan/Datsun nationals over easter which is being held at Phillip Island, should see some scary speeds down the start/finish straight!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
    • Decided for the first time ever I would tow my car TO the track day on the same working theory as bringing tools and spares "if I have it I wont need it, but if I leave it behind i will 100% need it" all setup and ready to go out and try these A050 for the first time First session showed I needed to stiffen up the dampers a touch but still managed a few 1:21's without much effort. things were looking good. Came in a dropped the tyres down  to 26/28 as they had gotten to 35/33C from 22C cold The first lap of session two I managed to drop into 1:20's. Then in the second lap into the second session. Coming into T3 and I suddenly lost brake pedal followed by some huge rear end vibrations and scraping sounds. Got it back into the pits after session ended and found this. in the attached video, all of the wobble is in the hub its self, wheel is mint, and bearing feels tight. lKXLqpd - Imgur.mp4   Deciding it was a bent spindle I tried to find bearing/hub assembly locally but was unsuccessful so it was loaded back onto the trailer i luckily brought it on to drag it back home  
    • 1.05 you’ve gotta let it breath 
×
×
  • Create New...