Jump to content
SAU Community

Recommended Posts

well i got my rb25det r31 and it free revs well.

But once you put load on it driving it starts to rev and then breaks down and wont rev, and starts backfiring as if it was a limiter noise...

when you change gears the bov makes a high pitched whistle instead of the normal rb25det bov noise, but thats in 1st and 2nd but from 2nd to 3rd and 3rd to 4th and 4th to 5th it makes the normal noises...

and when you do the limiter revving under load noise when you put the clutch in the revs drop down then it revs back up

free revs all the way out but wont rev under load

what could it be?

Link to comment
https://www.sau.com.au/forums/topic/160907-rb25det-breaks-down-under-load/
Share on other sites

coil packs or spark plugs. there are a few different fixes for the misfiring problem.

#1 - gap your spark plugs to .8mm (do that if not already done)

#2 - fix your coil packs, there are a few threads around on how to do this.

as for the bov sound, im not too sure if this fits the sound you described but it might be turbo chatter, where your bov doesnt actually open, the noise you're hearing is the air passing back onto the turbo blades.

Hey you are reading my mind but about four months earlier, If you have played with intercooler and a boost controller on the car you would have noticed that a nipple would be missing on the inlet part of the pipe before the bov that is the vacuum pipe that opens the actuator on the internal waste gate and if you dont have that hooked up you will hit max load causing seveire breakdown at 2k trust me i had the exact problem!!! easy way to fix it is to simply put a T valve in on the blow off valve hose that goes to near the back of the plenum!! that will get rid of your break down at 2k.. P.M if ya want a photo!

made a slight difference but still breaks down, but you can get past the banging and then it tries to pull.. could it be a fuel problem?

but what concerns me is, i gave it a boot full and then went to go into my driveway, stopped and the car stalled, then i started it again and it stalled again but started it and gave it a rev and it idled fine...

its quite farken easy u see...

u get a gapping tool, pick the gap u want, get ur spark plug out, tap them on the ground softly until the gapping ruler u are using fits between the sparking element and the underside of the tip. ur spark plugs come pregapped at 1.1 thats not enough for boost past 6-7psi. that will work, if ur unsure how to do it, go to ur mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...