Jump to content
SAU Community

Recommended Posts

well i got my rb25det r31 and it free revs well.

But once you put load on it driving it starts to rev and then breaks down and wont rev, and starts backfiring as if it was a limiter noise...

when you change gears the bov makes a high pitched whistle instead of the normal rb25det bov noise, but thats in 1st and 2nd but from 2nd to 3rd and 3rd to 4th and 4th to 5th it makes the normal noises...

and when you do the limiter revving under load noise when you put the clutch in the revs drop down then it revs back up

free revs all the way out but wont rev under load

what could it be?

Link to comment
https://www.sau.com.au/forums/topic/160907-rb25det-breaks-down-under-load/
Share on other sites

coil packs or spark plugs. there are a few different fixes for the misfiring problem.

#1 - gap your spark plugs to .8mm (do that if not already done)

#2 - fix your coil packs, there are a few threads around on how to do this.

as for the bov sound, im not too sure if this fits the sound you described but it might be turbo chatter, where your bov doesnt actually open, the noise you're hearing is the air passing back onto the turbo blades.

Hey you are reading my mind but about four months earlier, If you have played with intercooler and a boost controller on the car you would have noticed that a nipple would be missing on the inlet part of the pipe before the bov that is the vacuum pipe that opens the actuator on the internal waste gate and if you dont have that hooked up you will hit max load causing seveire breakdown at 2k trust me i had the exact problem!!! easy way to fix it is to simply put a T valve in on the blow off valve hose that goes to near the back of the plenum!! that will get rid of your break down at 2k.. P.M if ya want a photo!

made a slight difference but still breaks down, but you can get past the banging and then it tries to pull.. could it be a fuel problem?

but what concerns me is, i gave it a boot full and then went to go into my driveway, stopped and the car stalled, then i started it again and it stalled again but started it and gave it a rev and it idled fine...

its quite farken easy u see...

u get a gapping tool, pick the gap u want, get ur spark plug out, tap them on the ground softly until the gapping ruler u are using fits between the sparking element and the underside of the tip. ur spark plugs come pregapped at 1.1 thats not enough for boost past 6-7psi. that will work, if ur unsure how to do it, go to ur mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...