Jump to content
SAU Community

Recommended Posts

Just fitting my new JJ FMIC and am wondering where others have conected the Boost control hose that operates the actuator?

I have tapped into the BOV line for now and am wondering if that is good enough or not right at all?

I havent driven the car yet cos its not quite finished (Too noisy for the grinder this late) but want to know of any other methods!!

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/160912-just-jap-fmic/
Share on other sites

Only reason i asked about the BOV was cos it has vaccum aswell as boost pressure, but the way it was before it could only get boost pressure!!! So I just wanted to make sure it was OK before I kicked it over.

Link to comment
https://www.sau.com.au/forums/topic/160912-just-jap-fmic/#findComment-2988229
Share on other sites

i have seen others use the bov line and it having no problems

mine has a nipple attached to the first part of the piping that goes from the exit of the compressor to the inlet of the intercooler..

most people tend to think it should come from as close to the compressor outlet as possible..

Link to comment
https://www.sau.com.au/forums/topic/160912-just-jap-fmic/#findComment-2988392
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...