Jump to content
SAU Community

Recommended Posts

I think for me it comes down to getting a stainless mesh pod or a K&N pod.

The thought of the stainless mesh pod flowing heaps better is cool , but the thought of driving through it through a large dust cloud that a lawn mower or tractor or truck is kicking up and getting all that fine dust going straight through the filter isn't very nice.

I think I'll go for the K&N. Best protection and flows decent enough. the flow difference probably doesn't matter as much anyway on a car thats not putting out big power.

I run a stainless mesh filter, with a K&N Filtercharger sock. Looks pretty much like a shower cap. Flow performance is great, though in dusty conditions (grass/dirt motorkhana) the fine dust has shown signs of passing through the filter.

Slightly off track, but has anyone using a K&N ever reported an AFM failure due to contamination of the hot wire by the K&N oil?

A few of the guys on ns.com think its a sin to run oiled filters because it "stuffs up the AFM".

In my experience, I've had a oiled filter for about a year now and quite honestly no oil had contaminated of the afm or performance drop. No oil has even left the filter for that fact and coated the intake. The only time oil came though the filter is when I re-oiled it probably a tad too much. Just got some electrical contact cleaner and sprayed down the afm after I ran the filter for a few drives.

yeah, I never had a problem with an oiled filter and i ran one on one of my cars for nearly 3 years. and probably cleaned and oil it 3 or 4 times. buy the K+N maintenance kit. it comes with cleaner, and the spray on filter oil. the filter oil is red so you can see where you've sprayed and helps to make sure you don't over oil. i mean, you don't douse it in the stuff, it's just a light coating to aid in filtration.

K&N offer a lifetime warranty (ie 1million kms), I use them and have for years.

I use twin pods on my rebuilt CBR919RR engine, wouldnt use anything but K&N on that highly stressed engine with race flatslide carbies.

I use a single pod on my 190rwkw Rb25det, oil it every 6 months. When washing / cleaning / re-oiling the K&N filter, take off the afm and spray it with brake contact cleaner, to get rid of the last 6months oily residue.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...