Jump to content
SAU Community

Recommended Posts

I am looking at buying an R33 GTS-T from interstate.

What do i need to do if i want to register it here in SA? Does it matter if it comes with RWC or not?

Description-

130,000kms, 1994 model, genuine car, Rare Factory Black, 5sp manual with Electric Sunroof, Grade 3.5 Auction with NO accident histrory. Straight vehicle with good modifications, incl coilover supension, Blitz Adjustable Boost Controller, updated rear spoiler, Apexi N1 exhaust, Apexi Super AFC and Air intake, factory sunroof, runs very well, incl full compliance and RWC.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/161843-buying-r33-gts-t-from-interstate/
Share on other sites

RWC doesnt apply in South Australia..As far as Im aware of. Also as far as buying it interstate. When you bring the car into SA all you need to do is get the VIN number checked at regency or if your more than 50kms from there, a local cop shop and then you simply change over rego...Just try make sure the acar isnt moddded to much when going through regency or you will probably end up with a defect as well.

Good luck..

Beki :unsure:

Be sure your living 40km's out of the CBD so you can take it to the local cop shop for its identity check.

Otherwise its a regency job where they give it a brief looking over. :unsure:

So I was told when recently enquiring about the purchase of an interstate vehicle.

OR, you can get the owner to write a statement saying you have been living with them interstate for 3+ months, take it to a rego department over there, register the car in your name and then drive it back here. Then, all you need to do is fill in a form to transfer rego, no checks, nothing, simple :unsure:

Hi

I just recently bought a skyline from interstate exact same type as yours actually (black with sunroof) and you shouldnt have any probs getting it registered here, just make sure when your getting your vehicle id inspection done your car is pretty stockish looking cause i took mine to Sturt Cop shop and they had a full hard look over it. Other than that just make sure if you have tinting on car that its legal cause there really picky about that.

Edited by /2on

Hey,

Ive brought two R33's from interstate. Both through regency. No matter what they will do a VIN check ( was registered in my name in NSW ). First one was stock, just had an exhaust. Had no worries. Second one I bought in had tinted windows, exhaust, 18s stock air box. They wouldnt register it until i removed the window tinting. They are really big on window tinting and test every car, you won't get through with it on. Its not the same workshop that you would goto if you got defected. I found some of the employees there particularly unfriendly. Guess they have a shit job really. Its also rumoured that they check the passenger kick panel for aftermarket ECUs. If you can, make the car as standard and clean as possible when you go though, you will be fine.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...