Jump to content
SAU Community

Recommended Posts

Borrowed from Jay95's Leather Handbrake Boot installation instructions.....

What we need to do is take the centre console (the part between the two front seats)out of the car.

With the plastic surround that goes around the gearstick still off, undo the two screws that were under the plastic surround that you just took off.

Then open up the centre console bit and undo the two screws inside the compartment. If your car has duel airbags, then these two screws will be on the outside of the console, on either side of it. You can get to them if you move your seats all the way forward and tilt them forward too.

Once the screws are out, unbutton the to studs that are on the factory handbrake boot, then the whole centre console bit can be lifted up and forward to get it out of the car. Just be careful not to scratch your stereo with the console when you take it out.

Once the console is out of the car, turn it upside down and with the help of a small flat headed screwdriver, gently prise the handbrake boot out of the console.

The factory handbrake boot has a wire frame sewn around the base of it.

Once it's out of the console, you'll need to cut the wire frame out of the factory boot, and sew it into the base of the new boot. Just remember the way the frame is sitting in the factory boot. I'm pretty sure the high side of the wire frame goes to the drivers side.

Once the wire frame is sewn in, pop it back into the centre console and re-install the centre console and the plastic surround around the gearstick.

Whala - all done.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...