Jump to content
SAU Community

Recommended Posts

Hi All,

**i've posted this message in the Forced Induction forum however i think this forum is probably the better bet...

A mate has a R33 Series 1 which he has had a Series 2 block installed. However, the car now will not start. The car just doesnt seem to want to kick over.

I believe he has a set of Spitfire ignitor coils for Series 2 and he has had the wiring redone on the ignition side so it is compatible with the Series 1 setup. Was this required? would Series 1 ignitor coils in conjunction with the Series 1 ignitor pack work with the Series 2 block?

I've also heard that the wiring for the crank angle sensor needs to be re-wired as well.. is this true?

Lastly, the only things i can think of that could be causing the problem is that the crank angle sensor is faulty or the immobolizer is kicking in. My mate did have an alarm on his car, however is now not working.

So if anyone can help out, it would be much appreciated. Thanks in advanced.

Regards

Steve

Hi All,

**i've posted this message in the Forced Induction forum however i think this forum is probably the better bet...

A mate has a R33 Series 1 which he has had a Series 2 block installed. However, the car now will not start. The car just doesnt seem to want to kick over.

I believe he has a set of Spitfire ignitor coils for Series 2 and he has had the wiring redone on the ignition side so it is compatible with the Series 1 setup. Was this required? would Series 1 ignitor coils in conjunction with the Series 1 ignitor pack work with the Series 2 block?

I've also heard that the wiring for the crank angle sensor needs to be re-wired as well.. is this true?

Lastly, the only things i can think of that could be causing the problem is that the crank angle sensor is faulty or the immobolizer is kicking in. My mate did have an alarm on his car, however is now not working.

So if anyone can help out, it would be much appreciated. Thanks in advanced.

Regards

Steve

You will need to use either the series 1 ignitor with series 1 coils or series 2 coils. I'm guessing the series 1 wiring loom was used in which case it would be easier to simply use all the series 1 sensors eg CAS, AFM etc as the plugs are different. Its a little difficult to comment further without more information on what rewiring was done.

Hi,

Thanks for your reply... My mate is using the S1 coils with S1 ignitor module.

Would i need to be using a S2 AFM? or will the S1 AFM do fine as he is using all S1 wiring, ecu etc.

In regards to the CAS, is it as easy as removing the S2 CAS and installing the S1 CAS? does it fit without problems?

Any help would be great... going to check all the above, fuel feed, sparks in the next hour.

Hi,

Thanks for your reply... My mate is using the S1 coils with S1 ignitor module.

Would i need to be using a S2 AFM? or will the S1 AFM do fine as he is using all S1 wiring, ecu etc.

In regards to the CAS, is it as easy as removing the S2 CAS and installing the S1 CAS? does it fit without problems?

Any help would be great... going to check all the above, fuel feed, sparks in the next hour.

I would use all the series 1 gear including AFM (series 1 plug wont fit on the series 2 AFM). I checked the CAS and the plug is the same for series 1 and 2, but in any case I would suggest using the series 1 CAS if you know it was working with the series 1 motor. Yes you can swap the CAS without any problems.

Let us know how you go.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...