Jump to content
SAU Community

Recommended Posts

Hey peoples,

Have a brand spanking new top model Cadence Monoblock amp. Its a monoblock amp which pumps a friggen crazy 1500wRMS @ 1 ohm. Still in the box and all. Was going to be used in my current audio install, however i decided to go out and buy a fourth sub the other day so now i need to get two of the model below this one so i can run all four. As i said brand new, have receipts, and really don't want to sell it but need to get rid of it in the next week at the latest so i can get the new amp's and give them to the installer before it goes in to get the full show set up done. It cost me $1290 less than a month ago and has sat on my couch in my room since waiting to be installed. I am asking only $750 for it which is pretty damn good, and if someone is genuinely keen and will give me cash i will throw in my brand new un-used Stinger Pro 1 farad cap aswell for it worth $300!! As ya can see i really gotta just get rid of it so i can get all the new stuff installed asap. Its an absolute monster of an amp and will crank the biggest of subs hard as hell, i seen the same model used in a competition wining sedan with two of these amps and four Kicker solabaric L7 subs and they were quite simply... awesome.

Specs are:

4 ohm Power = 50 watts rated power

2 ohm Power = 750 watts rated power

1 ohm Power = 1500wRMS mono power

frequency response = 10Hz-40KHz

signal/noise ratio >100dB

damping factor >200 @ 100Hz

minimum THD <0.044%

channel seperation >65dB

Link to comment
https://www.sau.com.au/forums/topic/16290-brand-new-cadence-z700-1500wrms-amp/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...