Jump to content
SAU Community

Flashing Airbag light

skyline33

By skyline33,
in General Maintenance

 Share

Recommended Posts

skyline33 Grand Master

skyline33

Posted
  • Author
Posted

I did a search and found this but i'm not sure which is the driver door switch:

THIS IS HOW TO RESET THE AIRBAG COMPUTER

First you have to put the system into the diagnostic mode. Here's how to do this:

From User Mode To Diagnosis Mode:

Diagnosis Mode activates only when a malfunction is detected, by pressing the driver's door switch at least 5 times within 7 seconds after turning the ignition "ON". SRS will not enter Diagnosis Mode if no malfunction is detected.

From Diagnosis Mode to User Mode:

After a malfunction is repaired, switch the ignition "OFF" for at least 1 second , then back "ON". Diagnosis Mode returns to User Mode. If switching Diagnosis Mode to User Mode is required while malfunction is being detected, switch the ignition "OFF", then back "ON" and press the driver's door switch at least 5 times within 7 seconds.

After a malfunction is repaired, return to User Mode from Diagnosis Mode by switching the ignition "OFF" for at least 1 second, then back "ON". At that time, the problem code is cleared

AeroGrace Rising Star

AeroGrace

Posted
Posted

that happened to me once when I had the boost gauge put in airbag light went flashing whenever ignition was turned on, it happens when the car senses a voltage leak or something or other...but they finally cleared it all up and I believe it was with the instructions you got(they told me they got it from the internet too)

anyway, i believe the switch is the little black rubber button thingy on the drivers side door near where the sticker for the tyre specs should be, i saw him pressing it a number of times along with some other stuff he did.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...