Jump to content
SAU Community

Recommended Posts

Hey Guys

I recently installed a HKS mushroom filter on my S1 R33 (Auto) and noticed that the idle is running rough. Sounds almost like its missing a bit and revs at idle range from 400-900. The power on low end (10-40km) is really shite as well, feels really laggy. This is the only mod i've done to the car, everything else is bone stock.

The air filter was put on after a mate tried to get more sound out of the stock BOV. I.e. Plugged the plumb back hose and vented the BOV to atmosphere. We found that the car ran rough as guts, hunting at idle and stalling, but sounded great hahaha, so we put the BOV back to stock plumb back and just bolted on a mushroom filter. Later did some research and heard that stock BOV is always open just a little and idle was hunting due to lack of back pressure. Is this true?

My assumption is that the problem will be fixed after installing an after market BOV which stays closed when not venting. Will this fix the problem? Also I haven't reset the ECU after changing to mushroom filter, maybe give that a go????

Cheers

Link to comment
https://www.sau.com.au/forums/topic/163542-rough-idle-after-pod-install/
Share on other sites

How do you clean your afm?? Carby cleaner yeah but like do i open it up and spray in there? I would have thought this problem had more to do with air pressure?? Wouldn't know SFA though so any suggestions are welcome. Thanks for the replys so far guys

an aftermarket bov won't allow you to have it atmospheric because vacuum will still be strong enough to open it under normal driving conditions unless you tighten the bov more but then there is no point having a bov if it's too tight to properly vent pressure and cause flutter.

when your car is using an AFM its best to keep the bov plumbed back to the intake even if it's aftermarket because you're letting air that the AFM has sensed and added fuel for out of the system causing richness.

to put it simply every time you hear the bov vent you would be wasting fuel and your car would not run well.

Air Flow Meter!!! NOT Air Pressure Gauge..........

Who said Air Pressure Guage?? Can't find it anywhere on the page....

So Dobz..Are you saying that i can't have an atmospheric BOV??? How do other skyline owners do it? Plus i thought you have to have some sort of AFM all the time??? Confused.....

you can have an atmo BOV , you just need a good one which has a good spring and vents well . yes a lot of people have idle troubles because of them if not setup properly . try adjusting the bov , and watch your idle change . a cheap bov will cause numerous amounts of trouble because they arent made well - hopefully you have a decent one , for your own benifit.

here are some things to do :

ACC Valve : search ! . you will find a very well written DIY to clean everything out . your idle will run much better . you need carby cleaner for this - its a must !

AFM: clean it with carby cleaner aswell , spray it in the direction of the arrow on the AFM. there could be some debree attatched to it .

both of these will definitly help your idle if not fix it . remember to search before you post.

its most probably due to the bov not being plumbed back as the ecu is expecting that extra air being recirculated, i did the same of my gtst and it ran like crap plumbed it back and it was all good and because i had a pod put on you could still hear the bov pretty loud if thats what ur after. However i seen ppl not run plumb back systems and they ran fine, you can get a extra module to control ur idle etc, ive also seen ppl run two bovs, the original plumbed back and another one to the atmosphere which works too i guess.

The BOV is still plumbed back, changed that back to stock before adding the pod. I noticed last night that it behaves much better at night when the air is cooler than in the day, might sound stupid but it seemed heaps quicker than when stock. It's just in the day time that its really laggy from 0-40km/h.

Maybe the super special microchip in the pod is dirty. Try cleaning it and it will not only run better but give you 20 or 30more rwkw's . :laughing-smiley-014:

but in all seriousnes just try disconnecting the air flow meter and putting it back in again, also reset the ecu before starting car again. I ave had identical problem twice after mucking around with the pod filter and thats what fixed it for me..

good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...