Jump to content
SAU Community

Recommended Posts

Hey Guys

I recently installed a HKS mushroom filter on my S1 R33 (Auto) and noticed that the idle is running rough. Sounds almost like its missing a bit and revs at idle range from 400-900. The power on low end (10-40km) is really shite as well, feels really laggy. This is the only mod i've done to the car, everything else is bone stock.

The air filter was put on after a mate tried to get more sound out of the stock BOV. I.e. Plugged the plumb back hose and vented the BOV to atmosphere. We found that the car ran rough as guts, hunting at idle and stalling, but sounded great hahaha, so we put the BOV back to stock plumb back and just bolted on a mushroom filter. Later did some research and heard that stock BOV is always open just a little and idle was hunting due to lack of back pressure. Is this true?

My assumption is that the problem will be fixed after installing an after market BOV which stays closed when not venting. Will this fix the problem? Also I haven't reset the ECU after changing to mushroom filter, maybe give that a go????

Cheers

Link to comment
https://www.sau.com.au/forums/topic/163542-rough-idle-after-pod-install/
Share on other sites

How do you clean your afm?? Carby cleaner yeah but like do i open it up and spray in there? I would have thought this problem had more to do with air pressure?? Wouldn't know SFA though so any suggestions are welcome. Thanks for the replys so far guys

an aftermarket bov won't allow you to have it atmospheric because vacuum will still be strong enough to open it under normal driving conditions unless you tighten the bov more but then there is no point having a bov if it's too tight to properly vent pressure and cause flutter.

when your car is using an AFM its best to keep the bov plumbed back to the intake even if it's aftermarket because you're letting air that the AFM has sensed and added fuel for out of the system causing richness.

to put it simply every time you hear the bov vent you would be wasting fuel and your car would not run well.

Air Flow Meter!!! NOT Air Pressure Gauge..........

Who said Air Pressure Guage?? Can't find it anywhere on the page....

So Dobz..Are you saying that i can't have an atmospheric BOV??? How do other skyline owners do it? Plus i thought you have to have some sort of AFM all the time??? Confused.....

you can have an atmo BOV , you just need a good one which has a good spring and vents well . yes a lot of people have idle troubles because of them if not setup properly . try adjusting the bov , and watch your idle change . a cheap bov will cause numerous amounts of trouble because they arent made well - hopefully you have a decent one , for your own benifit.

here are some things to do :

ACC Valve : search ! . you will find a very well written DIY to clean everything out . your idle will run much better . you need carby cleaner for this - its a must !

AFM: clean it with carby cleaner aswell , spray it in the direction of the arrow on the AFM. there could be some debree attatched to it .

both of these will definitly help your idle if not fix it . remember to search before you post.

its most probably due to the bov not being plumbed back as the ecu is expecting that extra air being recirculated, i did the same of my gtst and it ran like crap plumbed it back and it was all good and because i had a pod put on you could still hear the bov pretty loud if thats what ur after. However i seen ppl not run plumb back systems and they ran fine, you can get a extra module to control ur idle etc, ive also seen ppl run two bovs, the original plumbed back and another one to the atmosphere which works too i guess.

The BOV is still plumbed back, changed that back to stock before adding the pod. I noticed last night that it behaves much better at night when the air is cooler than in the day, might sound stupid but it seemed heaps quicker than when stock. It's just in the day time that its really laggy from 0-40km/h.

Maybe the super special microchip in the pod is dirty. Try cleaning it and it will not only run better but give you 20 or 30more rwkw's . :laughing-smiley-014:

but in all seriousnes just try disconnecting the air flow meter and putting it back in again, also reset the ecu before starting car again. I ave had identical problem twice after mucking around with the pod filter and thats what fixed it for me..

good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...