Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

ive checked spark, took the coil pack out and earthed it on the engine through a screw driver (the professional way hahaha)

ill test the injector and resistor tomorrow when i can, im really leaning towards one of the injectors or resistors shitting themselves....

lol @ r31, really leaning towards a shitter to drive everytime my car dies!

Rb26 would be worth more than the car lol

ill get another rb20 and run 28psi lol

slide fly down and fix it for me, ill give you steaks..... :P

Ordered new resistors so should be coming today, cant fix it today so have to leave it here another night... lucky its safe! tomorrow is D day!

the injectors and resistors came in and out 6times, due to 68ohm resistors instead of 6.8 so i dont think that i woulda done a 110% job putting them in the last time! having the shits and all......

the loud clanging, metal noise was scaring the sheet out of me last night, but i figured out that since it was running so rough it was ossicilating down the exhaust and it was shaking on the mounts PHEW!

umm. have you got your range on the mutlti meter rioght? it sounds that its out by a factor of ten.

20 resister does all 6 (2wires). not individal like a rb26. whats the compression or all the cylinders. hows the sparkplugs, so its got spark on 5 and 1? if so its an injector or plug.

well bit of modding, rewiring and checking and she runs again..

even with the weird connection injector, which i want to get rid of asap...

Dave i sent you a PM about the 1 or 2 you have laying around?

Car atleast runs now, but drives like its had the shit thrashed out of it at a drift day by some hoon!!!!

New sparkies, oil and filters tomorrow! horray

still havent washed the mud off it hahaha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...