Jump to content
SAU Community

Recommended Posts

Hey, urgent question!

I am buying the CLARION VRX765VD from ebay, its being sent from America. But before I make the payment, does anyone know if this will definately work for Australian formats?

Will it work with Australian DVDs, Australian CD's, Australian Ipods etc. ?

I understand that the Australian model is called the VRX766VD....they look totally the same. Wat do you guys rekon? (Im getting the VRX765VD 500 bux cheaper then the VRX766VD (retail) )

Link to comment
https://www.sau.com.au/forums/topic/164847-would-the-vrx765vd-be-compatible/
Share on other sites

The VRX765VD is designed to play Region 1 DVDs (Aussie ones are Region 4). So no it won't play them, and as far as I'm aware there is no way to unlock the VRX765VD.

Hence one of the pitfalls of buying international. No local warranty support, some features may not here.

How much are you paying for it by the way?

790 for the VRX765VD

or

1300 for the VRX766VD

Razorsharp, are u 100% sure?

http://www.clarion.com/us/en/MungoBlobs/44...RX765VD-ENG.pdf

Manual, page 21: "...will only play DVDs with the region number '1' or 'ALL'"

CDs and Ipods should play fine.

Weigh it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The frontend wouldn't go low enough because the coilover was max low and the upper control arm would collapse into itself and potentially bottom out in the strut tower. I made a brace and cut off the kingpin and then moved the upright down 1.25" and welded. i still have to finish but this gives an idea. Now I can have a normal 3.25" of shock travel and things aren't binding. I'm also dropping the lower arm and tie rod 1.25".
    • Motor and body mockup. Wheel fitment and ride height not set. Last pic shows front ride height after modifying the front uprights to make a 1.25" drop spindle.
    • Here's Logans Silvia with R32 Drivetrain, mine will be slightly lower (more angle). He was constantly blowing the RH axles at around 16deg. I want to avoid this.    
    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
×
×
  • Create New...