Jump to content
SAU Community

Recommended Posts

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

cool...thanks grant.

mate has a set of eurolines ..18*9 and 18*10 ..both with +35 offset...i'll try them for fit this weekend....oh and tyres are 235 at the rear too...really stretchhhhhed

wont fit in the rear it WILL hit the coilover, you need a 25mm spacer to clear them

the front will be kinda sunken

BUT if you put the 10 in the front you would be fine, but it woudl be stupid

Nice, Marc. Must come back to Canberra to have a sticky-beak...

Front 18x9 +30 Rays GT7, Proxe(?) 235x40x18

Rear 18x10 +32 Rays GT7, Maxxis 245x40x18 plus 3mm spacers.

Prior to WA road rego was tyres rear Proxes also, 265x35x18 but self destructed between Brisbane & WA. (bugger)

Ride height ~380mm all round. At this time.

cheers GW :ermm:

edit. plate removed.

Edited by 260tech

I thought the R33/R34/Stagea AWD system was like other AWD's - in the fact that you have to run the same size tyres front and rear?

Is this not the case?

I know you can get away with it for a while, but you'll end up burning out your drivetrain, correct?

I thought the R33/R34/Stagea AWD system was like other AWD's - in the fact that you have to run the same size tyres front and rear?

Is this not the case?

I know you can get away with it for a while, but you'll end up burning out your drivetrain, correct?

Ref wheel diameters/profiles front to rear, I'm sure you are right however my GTIR equiped son tells me that my car is only 4wd when the rears break away & to date I have not achieved this. Too busy messing around with it plus tyres cost $$$$$$$$$$$$$. The 35's came with it of the boat so could well have been half shagged before it got into my hands. By the time I got it to WA they was chewed out on the inside edge. I will not be fitting that profile in the future unless it is all four.

Cheers GW :wub:

how much lower are you than stock?

nevermind.

i guess i really DID have that much camber lol

looks good man!

I would say about stock height. Any lower & it slurps up beer cans off the road.

Cheers GW :wub:

i pulled it becuase i hate 4wd

its still pulled now.....

im not in snow or slick surfaces, so i dont need 4wd.... its overrated around my area...plus i like drifting and big smokey burnouts

i pulled it becuase i hate 4wd

its still pulled now.....

im not in snow or slick surfaces, so i dont need 4wd.... its overrated around my area...plus i like drifting and big smokey burnouts

Why did you get a Stagea again?

i pulled it becuase i hate 4wd

its still pulled now.....

im not in snow or slick surfaces, so i dont need 4wd.... its overrated around my area...plus i like drifting and big smokey burnouts

i've had a galant vr4 engine with a gsr 4wd gearbox fit in a lancer before which in fwd mode.....mechanics had to weld something in the tranny to stop the rear from spinning....did you have to do the same when going rwd?

  • 2 months later...

in answer of nz_26t question on whats the bigest rims you can fit under a serries one stag (i answed it here as i belive we should keep this thread alive.) my friend has a serries one 96 model and has just recently fitted 20x7's not shure on the rest as i don't speak to him much any more.

don't happen to have any pix do you of the 20's on?

any problems putting them on with guard clearance & so forth?

sorry fuzzy as i said don't talk to him much and haven;t seen him in a while. all i do know is he got his serries one stock, fitted exsahust and got it lowred by reseting the factory springs only resulted in 30mm drop. wacked on 17's then upgraded to 20's after ruining a 17. no gaurd removal just bolted them on no spaces and i think it looks f#@ked the rims sit to far in and it looks like a monster truck it's that high off the ground. as i said though there only 7" wide if you are going to get some get them through a reputible dealer and get the write off set. lower it as far as possible then even get a body kit so it looks low and suits the rims

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
×
×
  • Create New...