Jump to content
SAU Community

Gauge Wireing

R TUNE

By R TUNE,
in General Maintenance

 Share

Recommended Posts

R TUNE Mentor

R TUNE

Posted
Posted

hey guys can people tell me how they have wired up thier gauges (pref 5).

i have the following.

oil pressure (drift neo)

oil temp (signal to be wired up) (drift neo)

volt (drift ignight)

water temp (drift ignight)

air fuel/ratio. (drift ignight)

all my gauges are being powered by the cig lighter circute (power earth and light switch), how ever to night i noticed that if i turned the lights off the water temp would fall by 15 dec and oil pressure would rise by 4psi. turn the lights on water temp rises by 15 dec and oil pressure drops 4psi. these were all so (not oil presser tho) affected when i applyed power while sitting in nurtral. can someone advise me on how to best wire up my gauges please.

chears brentt

Link to comment
https://www.sau.com.au/forums/topic/165146-gauge-wireing/
Share on other sites
Omurru Veteran

Omurru

Posted
Posted

lol there's something dodge going on there.....stealing power/grnd/light from the ciggy lighter should work fine as it's only the power. For the gauges to be doing that something must be affecting the sense lines. Are they electronic or mechanical gauges? and i suppose the other obvious question where have you put all the sensors.....

Link to comment
https://www.sau.com.au/forums/topic/165146-gauge-wireing/#findComment-3059205
Share on other sites
R TUNE Mentor

R TUNE

Posted
  • Author
Posted
lol there's something dodge going on there.....stealing power/grnd/light from the ciggy lighter should work fine as it's only the power. For the gauges to be doing that something must be affecting the sense lines. Are they electronic or mechanical gauges? and i suppose the other obvious question where have you put all the sensors.....

all the gauges are electrical.

the water has the sender located in the top radiator hose, air/fuel ratio wire is connected at the o2 sensor, and oil presser is connected to the gauges own oil pressure snder unit which is on the block. however i do have all the wires running near each other could this be the problem. also the power wire for the audio runs near them.

Link to comment
https://www.sau.com.au/forums/topic/165146-gauge-wireing/#findComment-3060812
Share on other sites
Omurru Veteran

Omurru

Posted
Posted

Having all the gauge wiring running together should be fine. The audio power wire may cause a problem but I really doubt it, pull the fuse on the audio wire and see if you still get the problem...just to be sure it's not that. If you still get the problem I really have no idea :P Are the gauges all separate or do they run of a control box?

Link to comment
https://www.sau.com.au/forums/topic/165146-gauge-wireing/#findComment-3060984
Share on other sites
R TUNE Mentor

R TUNE

Posted
  • Author
Posted
Having all the gauge wiring running together should be fine. The audio power wire may cause a problem but I really doubt it, pull the fuse on the audio wire and see if you still get the problem...just to be sure it's not that. If you still get the problem I really have no idea :P Are the gauges all separate or do they run of a control box?

all the gauges are seperate. ill try pulling the fuse out. one of the guys from the r31 club sugested runing some decent size gauge wire from the battery to fuesed relay then to the gauges.

Link to comment
https://www.sau.com.au/forums/topic/165146-gauge-wireing/#findComment-3061000
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      You Gregged a whole racetrack!?
    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...