Jump to content
SAU Community

R33 Coil Overs Dump Pipe , 32 Head , To4 ,rubber Intake N More

KLR33
 Share

Recommended Posts

KLR33 Community Regular

KLR33

Posted
Posted (edited)

for sale

r33 a set of kei office coil overs with tops no leaks looking for 750 down to 650

r33 a 3 inch dump / front pipe good nic no rust or dents 100

r33 gtr n1 nostrils bought from just jap for 140 never used for 130 down to 100

top end of r32 rb20 head inlet manifold polished coil pack cover not sure what its worth so make a offer

to4 garret non ball bearing .6 front and 1.15 rear not chinese brand new cost me 1100 will sell for 850

stock exhaust manifold heat sheild 20 bucks

r33 rb25 t 6 coils and loom 100 bucks

r 33 turbo rubber intake good nic no cracks 50 bucks

pics of some stuff

http://s135.photobucket.com/albums/q147/si...a%20S13/r%2033/

located in sydney welcome to come check m out

post up or pm if u r interested will post at buyers expense

selling as i have to much stuff and too much debt

Edited by KLR33
  • 4 weeks later...
madaz R33 Proficient

madaz R33

Posted
Posted (edited)

howdy, intereseted in coil packs and loom (it is for a r33 gtst?),can u tell me the condition of coil packs and why u are selling ? where are u located? cheers Damo

Edited by madaz R33
KLR33 Community Regular

KLR33

Posted
  • Author
Posted
howdy, intereseted in coil packs and loom (it is for a r33 gtst?),can u tell me the condition of coil packs and why u are selling ? where are u located? cheers Damo

condition of coil packs is good no cracks or burns

i m selling because i sold my r 33 so i dont need the spares

located 5 mins from liverpool

pm me if u wana come past n check m out

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...