Jump to content
SAU Community

A Question For A31 Ceff/c33 Laurel/r32 4-door Owners.

R31 drift pig
 Share

Recommended Posts

R31 drift pig Experienced

R31 drift pig

Posted
Posted (edited)

Ok long story short.... :rant:

I own a R31 RB20DET, and getting a kit for it is nigh on impossible unless I fork out over $2500 for the R31 House kits, which, for a drift car, is a little silly.

Ive been looking at a Lot of R31 House's cars and they use a lot of other cars kits ie Ceff and Laurel, modded to suit the cars.

Im after the Side skirt dimensions for All 3 of the above mantioned models, as you can buy copy kits rather cheap.

I already have a R31 House copy front lip, and was considering C33 laurel URAS sides and rear, but wish to know dimensions before I do anything.

veloce3248img600x450117vd3.jpg

A31 URAS side skirts^^^

gtw4dk0.jpg

C33 Laurel URAS sides and rear bar^^^

To me it seems they cut the rear bar and fibreglass it onto a stock rear bar.... and the A31 URAS sides are simply cut to fit....

Heard a few rumours that R32 4 - Door sides fit, and if so, a set of Vertex sides would do the job quite nicley. :P:(

Ive tried emailing R31 house, using a translator, but I got a reply in Kanji and I cant translate it. :rant: :rant:

I know that some think kits and such are stupid, but Ive pretty much done everything else, bodykit and paint plus my cage(which goes in on the 23rd of june) were the last on my list.

To sum up, Im after Side skirt lengths on the Above mentioned 3 cars.... A31, C33 and R32 4 - Door. Need the actual length of the side of car, not the sideskirt.

Thank you all in advance.

Ben. :):rant:

Edited by R31 drift pig
R31 drift pig Experienced

R31 drift pig

Posted
  • Author
Posted

Already looked there... tried URAS aus, Monkey warehouse and Jetspeed.... they didnt have any in stock to measure. Im not ordering them in if they wont fit. :)

Trying Viva Garage tomorrow

Anyone? Just need someone torun out to their car with a tape measure and get the bottom wheel arch to arch measurements (where a sideskirt would bolt on) for a C33 and 32 foor door... mate has a A31 and checking his tomorrow arvo.

Any help would be appreciated. :):(

Thanks Guys.

R31 drift pig Experienced

R31 drift pig

Posted
  • Author
Posted

That would be much appreciated mate.... >_<:yes:

Now for a C33 laurel owner.... :santa::thumbsup:

And yes, that red 31 coupe is the hottest thing ive ever seen. RB26DET as well

Cheers, Ben.

R31 drift pig Experienced

R31 drift pig

Posted
  • Author
Posted
Hey ,

a31 and c33 are identical for side skirt fitment.

I have a pair of Uras skirts that I want to get rid of as well as a rear bar to suit cefiro.

Where do you live ?

Could do some trial fitting???

PM me.

PM'd you about those sideskirts previously....

You have new PM.

Cheers for all your help guys...

  • 11 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...