Jump to content
SAU Community

High Hp Rb30 Mods.. Whats Required 700-800hp

GDZ1LA

By GDZ1LA,
in Engines & Forced Induction

 Share

Recommended Posts

GDZ1LA Enthusiast

GDZ1LA

Posted
Posted

im about to start a high hp 30 motor. i know most of the things require but have i missed any out and what weakness are there at 700-800hp.. i dont want to do anythin thats not realy vital but any suggestiong would be great

30e block..30e crank will need big end grinding..

carrillo rods,, wisco pistions (good coice?)

std gtr oil pump ?ok?

knife endged and balanced crank (inc flywheel & power enterprice pully)

and thats pretty much what def will be getting done..

will be for dyno runs only at high power.. and maybe drag at lower power levels,

things im not sure about are (to save on build costs)

o ring block? or any extra block strengthing.

trust oilers on main bearing trust?

head studs? main studs? vs std gtr ones.

any heat treating/coatings?

26 mains and grinding channel in 30e block?

oil squirter fitting?

or any think else i have missed?

i dont want to do anythin thats not realy vital but any suggestiong would be great. ps that 30 post is far to big and its full of crap most and cant sniff out important info..

Adriano Grand Master

Adriano

Posted
Posted
im about to start a high hp 30 motor. i know most of the things require but have i missed any out and what weakness are there at 700-800hp.. i dont want to do anythin thats not realy vital but any suggestiong would be great

30e block..30e crank will need big end grinding..

carrillo rods,, wisco pistions (good coice?)

std gtr oil pump ?ok?No, at least an N! pump with crank collar

knife endged and balanced crank (inc flywheel & power enterprice pully) I also got the crank cryogenically treated

and thats pretty much what def will be getting done..

will be for dyno runs only at high power.. and maybe drag at lower power levels,

things im not sure about are (to save on build costs)

o ring block? or any extra block strengthing.Not needed

trust oilers on main bearing trust????

head studs? main studs? vs std gtr ones. Yep, ARP do these, retap block to take Rb26 head studs

any heat treating/coatings?Recommend getting pistons coated

26 mains and grinding channel in 30e block?????

oil squirter fitting?Good idea, but aparently very difficult to do(about to find out)

or any think else i have missed?

i dont want to do anythin thats not realy vital but any suggestiong would be great. ps that 30 post is far to big and its full of crap most and cant sniff out important info..

GDZ1LA Enthusiast

GDZ1LA

Posted
  • Author
Posted

its because the info is so bitsy its spread out on the sticky and most people arent actually answering the questions just talkin shit.. kinda like now.. if you canno help be please dont bother posting... anf you rite.. i dont have 3 weeks either.. i would rip my hair out before then im already since of the smack talk on there..

GDZ1LA Enthusiast

GDZ1LA

Posted
  • Author
Posted
For a 'reliable' 700-800hp, everything will need to be modified or changed, particularly the valve train and head porting (you are using the SOHC 12V head, yeah?)

what is everthink..?? what have i missed mentioning

im using nothing less than a rb26 head jun intake 85mm throttle medium porting and mild apexi cams & pullies.. im more consorned about the strength mods not the head mods.. i know my head and turbo setup can make the power.. i just want it to hold down below..

GDZ1LA Enthusiast

GDZ1LA

Posted
  • Author
Posted (edited)

can anyone helpme on some of these things..

things im not sure about are (to save on build costs)

o ring block? or any extra block strengthing.

trust oilers on main bearing trust?

head studs? main studs? vs std gtr ones.

any heat treating/coatings?

26 mains and grinding channel in 30e block?

oil squirter fitting?

whats required and whats not or any others i have missed

Edited by GDZ1LA
2BNVS Veteran

2BNVS

Posted
Posted

i just built mine to handle 700rwhp tops

basically need everything done yes.... pm me for more info, i could try send ya a list of my mods, theres just way too many here to list

get 1/2 inch head studs, block studs, if u can get the turbo, mani and dump coated then do that, i use a trust oil pump, was using gtr oil pump before but definatley dont want to risk it.....

ben...

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

GDZ1LA - Please read the RB30 sticky and also search.

There is more than enough info on what your asking about this forum.

People cant be expected to answer/repeat themselves time and time again.

If you do truly want to build a 700-800hp motor, then taking the time to read a detailed thread should be the least of your issues.

Rushing into a build is what will be the sad end to it.

Thanks

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
×
×
  • Create New...