Jump to content
SAU Community

Recommended Posts

Hey guys

we all know that buying a new set of rims can be a very expensive experience. but what people dont know, is that painted up stockies look pretty good still on the skylines and they are a cheap way of dressing up your car.

ive seen some threads through the other sections and thought that i would write a quick tutorial on how to do it yourself.

COST: approx $25-$30

MATERIALS: 2 x cans of paint (colour)

1 x primer/filler can

1 x clear coat can

DURATION : 6-8hrs for a great finish

4-6 slightly rushed but good enough

DIFFICULTY: low

Step 1. Remove your stockies from the car, i suggest putting the whole car on jack stands and doing all 4 rims at once. saves time and headaches too.

Step 2. Thoroughly clean your stockies with degreaser and soap and water to remove all residue from them.

Step 3. After stockies are dry, use metholated spirits or turps to clean the mag. it will give a good base to work from aswell as ensure all crap os off the mag. Now mask up the wheel surround using a ring of tape first and then on top of that place torn up newspaper and stick down. see pictures.

post-31466-1177751573.jpg

post-31466-1177751588.jpg

Step 4. apply first coat of primer/filler. i used the septone brand filler/primer available from supercheap auto for about $13 a can. 3 coats are needed with about 10mins inbetween coats. after the final coat allow 1 hour to dry properly and then using a scotch brite pad, give a very light rub over. this will provide an adequate base for the colour.

post-31466-1177751851.jpg

post-31466-1177751642.jpg

Step 5. apply first layer of colour to rim. Allow 10 mins between coats, light 1st coat is required and then 2 slightly heaveier coats. allow 1 hour before clear

post-31466-1177751664.jpg

Step 6. apply a 2 layers of clear to each rim. that will allow a durable finish. again 10mins between coats and 1 hour before putting the rims back on to your beast.

post-31466-1177751783.jpg

ive had 2 different colour rims now so have pics of the first 1 in black and the second in white will be up shortly once i get enough daylight to get a good shot.

post-31466-1177751943.jpg post-31466-1177751979.jpg post-31466-1177752029.jpg

hope this helps any1 else out in the same boat as i was, strapped for cash, splash some paint on your stockies

haha nice work! was bored out of my mind today. will do this in the morning. one question though, do the stockers have a clearcoat on them? coz mine have white discolouration and slight webbing. i thought it was because the wheel cleaner i was using was too harsh. this is gonna need stripping bak b4 i prime isnt it?

i found with clear coat it left a slight yellowish tinge to the rim, where as a coat without clear was bright white.

preperation is vital in gettin the colour perfect. just use 600-800grit sand paper to smooth the rim and the 3 coats of filler will cover almost all minor scratches so they wont be visible.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...