Jump to content
SAU Community

Recommended Posts

After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/167583-stock-exhaust-performance-gains/
Share on other sites

Yeah, I actually think the stock system sounds really good too. But if power is what you want it has to go, as far as noise goes you don't have that much of choice because aftermarket manufactures obviously design them to be louder for that sportier sound and better flow. What you could do is buy a decent 3" system off greenline.jp and add another resonator to reduce noise.

Edited by BAMR33
After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

change the front/dump, and put a bigger cat - i think that would be a good start. I got the front/dump, large cat and the trust pe2 cat back...good performance gain, very quiet too. dynoed at 164rwkws at re customs.

get a front mount - just jap (for around 400), second hand apexi power fc ecu, tweek turbo to around 11psi - get a full tune. not sure what the power rating will be like though.....

someone can correct me if im wrong with those mods......(probably dont need the power fc - but most people have it)

i discovered a quiet exhaust is a pretty large restriction

i went from a stocko, to a blitz jobby with an extra muffler

was quiet as (missus request) but robbed me of a fair bit of power (around 30rwkw)

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB on back off and 90dB on ramp up, has also a mid muffler and i had my sky tined last week at 168rwkw. only other mods are fmic, k&n panel filter and grounded out boost solenoid at 8psi. runs well enough.

guy i got the exhaust off said he had it tuned on his car and with it was still making 198 at the rears. IMHO, epa should go get fuc*ked. leave us to modify how we like as long as our pollution emissions are fine and the mods are rw. who cares if its a lil loud. ecu, pod, fmic, boost, wats it got to do with em. bloody poofters.

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

  • 2 weeks later...
Fujitsubo make excellent exhausts for what you are after. They are quiet at idle and at cruise and have a decent sound when on full song.

My old R33 ran a Super Ti from memory, was great.

Thanks I will look into that.

I'm going to see if I can get the exhaust off my wreck and repair it. The front pipe and cat looked fine, but the catback was dented and the muffler a bit squashed... don't know how much it's going to cost me. Might have to replace the muffler altogether?

Is there much point just putting split dump/front pipe + hiflow cat on? Might free it up a bit without being noisier.

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

Any idea how many dB a stock exhaust system would be?

Edited by bombastic
  • 2 weeks later...
good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

I think you're confusing something here - 92dB would be OUTSIDE the car, probably measured near the exhaust?

For a free-flowing exhaust thats still fairly quiet (sometimes inaudible when cruising at 50-60), make sure you get 2 mufflers, no resonators or anything. I've got a 3" oval magnaflow muffler at the rear and another 3" oval muffler in the middle. Being a wagon I need it quiet to reduce drone!

Its definitely quiet enough but not as quiet as stock.

To make it quieter and still get good flow, use twin pipes...although this will cost more.

It seems you either get good power, or a whisper quiet exhaust, but not both. Also I wouldn't bother doing other mods when you have the stock exhaust, except maybe just an SAFC or something - to maybe save a bit on fuel? Other than that, be aware that adding more boost pressure (ie. more psi) will likely just put more stress on your turbo without actually flowing more air through your engine (it could actually flow less!). psi is a measure of pressure, not necessarily airflow. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...