Jump to content
SAU Community

Recommended Posts

After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/167583-stock-exhaust-performance-gains/
Share on other sites

Yeah, I actually think the stock system sounds really good too. But if power is what you want it has to go, as far as noise goes you don't have that much of choice because aftermarket manufactures obviously design them to be louder for that sportier sound and better flow. What you could do is buy a decent 3" system off greenline.jp and add another resonator to reduce noise.

Edited by BAMR33
After writing off my first R33 (lesson learned, I won't do it again, promise!), I'm looking at another... I tried other cars but just keep coming back to the R33 :)

Anyhow. Have driven a few and some had the stock exhaust, I really liked the sound of it, so quiet.

I'm just wondering if I bought one and decided to keep the stock exhaust, what mods are worth doing? I've still got a powerfc from my old car, but I'm just wondering whether there will be much gains to be had in having it tuned? With say, an R34 SMIC and 10-12psi.

Or maybe there is a more free-flowing alternative available which doesn't add noise?

Sorry if this has been covered before, I searched for "stock exhaust" and didn't turn much up.

Cheers!

change the front/dump, and put a bigger cat - i think that would be a good start. I got the front/dump, large cat and the trust pe2 cat back...good performance gain, very quiet too. dynoed at 164rwkws at re customs.

get a front mount - just jap (for around 400), second hand apexi power fc ecu, tweek turbo to around 11psi - get a full tune. not sure what the power rating will be like though.....

someone can correct me if im wrong with those mods......(probably dont need the power fc - but most people have it)

i discovered a quiet exhaust is a pretty large restriction

i went from a stocko, to a blitz jobby with an extra muffler

was quiet as (missus request) but robbed me of a fair bit of power (around 30rwkw)

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB on back off and 90dB on ramp up, has also a mid muffler and i had my sky tined last week at 168rwkw. only other mods are fmic, k&n panel filter and grounded out boost solenoid at 8psi. runs well enough.

guy i got the exhaust off said he had it tuned on his car and with it was still making 198 at the rears. IMHO, epa should go get fuc*ked. leave us to modify how we like as long as our pollution emissions are fine and the mods are rw. who cares if its a lil loud. ecu, pod, fmic, boost, wats it got to do with em. bloody poofters.

im running a 3" straight dump pipe, hi flow cat, and jasma approved cat back exhaust, its like 92dB

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

  • 2 weeks later...
Fujitsubo make excellent exhausts for what you are after. They are quiet at idle and at cruise and have a decent sound when on full song.

My old R33 ran a Super Ti from memory, was great.

Thanks I will look into that.

I'm going to see if I can get the exhaust off my wreck and repair it. The front pipe and cat looked fine, but the catback was dented and the muffler a bit squashed... don't know how much it's going to cost me. Might have to replace the muffler altogether?

Is there much point just putting split dump/front pipe + hiflow cat on? Might free it up a bit without being noisier.

good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

Any idea how many dB a stock exhaust system would be?

Edited by bombastic
  • 2 weeks later...
good for you, but your opinion is irrelevant here. 92dB is a long way from being quiet, in fact 84dB is the cutoff for continuous exposure without hearing damage. if you want to beat your chest about having a loud exhaust find somewhere more suitable.

I think you're confusing something here - 92dB would be OUTSIDE the car, probably measured near the exhaust?

For a free-flowing exhaust thats still fairly quiet (sometimes inaudible when cruising at 50-60), make sure you get 2 mufflers, no resonators or anything. I've got a 3" oval magnaflow muffler at the rear and another 3" oval muffler in the middle. Being a wagon I need it quiet to reduce drone!

Its definitely quiet enough but not as quiet as stock.

To make it quieter and still get good flow, use twin pipes...although this will cost more.

It seems you either get good power, or a whisper quiet exhaust, but not both. Also I wouldn't bother doing other mods when you have the stock exhaust, except maybe just an SAFC or something - to maybe save a bit on fuel? Other than that, be aware that adding more boost pressure (ie. more psi) will likely just put more stress on your turbo without actually flowing more air through your engine (it could actually flow less!). psi is a measure of pressure, not necessarily airflow. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...