Jump to content
SAU Community

Recommended Posts

Don't stress Ash, I get it.

...it seems that one of the questions has since been edited to make it a bit more clear :(

i live in sydney - so i don't know if these rules differ from state to state.

Yes, they do.

If you live in Sydney, go and ask for info in the NSW section so that you can get the information which relates to you.

No point in changing everything if you don't have to.

this sucks! i have exactly the same problem in my r33 gtst, when i got pulled over on sydney rd coburg, the cop took a photo of my engine bay when he saw my BOV and said thats bad news 'expect a letter from EPA' and bye. i asked if that was legal for him to take a photo, and he said nothing just 'wait for a letter and you will be told wat to do' and he left like that. 2 weeks later i got the letter and after asking for an extension due to work and wasnt approved cause my letter for extension was too late now i have a suspended rego too, so cant even drive it.

i have a HKS BOV, 4inch exhaust, turbo timer, boost controller, intercooler, but no pod and i need to replace them with standard parts very quickly cause its due at EPA on the 29th of may, so if anyone can help that would be great, i will gladly swap my parts with stock BOV and exhaust with cash difference. i wont ask for much depending on condition, as my BOV and exhaust are still in good condition. so please help it will be gladly appreciated, my number is 0421 795 757. SAM

cheers

Edited by habibz_r33

Have you tried ringing up the epa, or going on the epa websites and getting the pdf download on all the modifcations you are allowed to have etc. It's all stated on there website. And yes they do check your car thouroughly. i put mine back to full standard as it was out of the factory. they plug a computer into ur car which checks all the settings for carbon monoxide etc. The guy there is good to not as bad as you would think.

Sounds way too usual.

The copper is right, you can only have 1 air induction mod. There's no way you will lose your intercooler, right? Hence, just source a standard airbox from somewhere and get rid of the Pod filter. Pod filters (unless enclosed and a proper CAI is employed is shit-house as it sucks way too much hot air from the engine anyways), BOV has to go, if you have a turbo controller that has to go to.

The copper should have given you a nice yellowy canary - just follow that. After you've demoded everything, go get a full RWC done, then bring it to a VICROADS office, they will inspect your vehicle then will stamp the canary as APPROVED and then you're free again.

With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

If it's only an exhaust noise test - then an authorised exhaust shop can do the noise test. They don't care about all the other mods, just that it is under the legal limit.

If it's a full blown EPA test - wrong info. EPA are interested in all things that may affect emissions - cams, turbos, intercoolers, pods, afms, computers etc etc.

so you can't just rock up with a FOT and a factory exhaust and it'll pass. Factory everything (except one intake mod) is the order of the day. Good luck if this is the case.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

Vicroads wouldn't know their a$$hole from their earhole. No good asking them if it's "legal" to mod it. Read the legislation and interpretive explanations (and guidelines) - that's the law and it can't be changed. Don't ring em and ask them - the person on the other end of the phone doesn't care or know.

Also, an approved Vehicle Engineer still won't approve something that in their opinion is not safe - eg cutting the front reo to fit a FMIC.

Note to all - check all state legislation before modifying, at least know what you are getting yourself into.

Sounds way too usual.

The copper is right, you can only have 1 air induction mod. There's no way you will lose your intercooler, right? Hence, just source a standard airbox from somewhere and get rid of the Pod filter. Pod filters (unless enclosed and a proper CAI is employed is shit-house as it sucks way too much hot air from the engine anyways), BOV has to go, if you have a turbo controller that has to go to.

The copper should have given you a nice yellowy canary - just follow that. After you've demoded everything, go get a full RWC done, then bring it to a VICROADS office, they will inspect your vehicle then will stamp the canary as APPROVED and then you're free again.

With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

Ok thats handy advice.. But DO i have to go through the whole Ordeal with Vicroads??? when i purchased the car, the previous owner went and got a roadworthy done, and that was roughly 2.5 months ago, So i have to do all that shit again?? If Vicroads cleared this car as roadworthy less than 3 months ago. does it not Override what ever the hell the EPA say?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...