Jump to content
SAU Community

10 Inch Vs 12 Inch Sub

Trav33

By Trav33,
in Car Audio & Electrical

 Share

Recommended Posts

DRD-00F Grand Master

DRD-00F

Posted
Posted
i have to 2x 10's at the moment, entry level eclipse SVC 200rms per, reveiving 250rms per, in a total of 1.9cuft and they sound fantastic, consistant 137dbs! upgradign to 2 Soundstream 10's(750rms) they will be fiberglass in the corners of the boot to retain the centre boot space.

fiberglass enclosures are your friend!

Please don't quote dbs unless it was done proffesionally...

i have run (not all at the same time) 1 x 10", 1 x 12", 2 x 10", 2 x 12", and to be honest there isn't a lot in it. a single 12 will sound better than a single 10" but once you go double they sound similar. i ran 2 10's in a festiva and if you cranked it up you could make the engine stall. it would make you feel sick after about 1 song

Im assuming standard battery and tiny wires with horrible ground points in a plastic car? :(

for the record i have run (not all at the same time):

1x10 (1 setup)

1x12 (3 dif setups)

2x12 (5 dif setups)

3x12 (1 setup)

1x15 (2 dif setups)

2x15 (1 setup)

EvilINGT Community Regular

EvilINGT

Posted
Posted

I have a CDT 12" sub in the boot tucked into the drivers side corner, very small im pretty sure my ICE guy said it was 1.2 cubic foot enclosure. Not 100% sure, but i believe this is about the smallest enclosure you can put this sub into. Awesome sound quality without too much big boomy bass, im pretty sure it would be a lot louder with a bigger enclosure though. BTW it runs of a single DD 1000W Amp, enough kick for 2 of these subs.

Just look for a sub that does what you want, check the specs you would be surprised the kind of enclosures that some subs require.

http://cdtaudio.com/testreport_2.htm a review of the sub on the CDT website

post-11434-1187249723_thumb.jpg

cheers

Evil

Plat Rookie

Plat

Posted
Posted

from my experience it depends what speakers you have, in order to match for the bass, my 10" alpine x sound great at low volume but drops off very quickly as its increased trying to keep up with the 4 amped 6" speakers

im currently running 2 12" boston G2's, they are exelent take up a bit of room but i swap back to my 10" for trips out of town for the weekend

EvilINGT Community Regular

EvilINGT

Posted
Posted

Good point about the speakers. I have CDT 6.5 Splits up front and Alpine Type R Coaxials in the back running off a Lanzar Amp. I find as long as you have the ability to adjust the volume on your sub/s then turning the volume down is not so much an issue. I am frequently reaching for the sub control as i listen to a range of different music styles. Im lucky my headunit can control the bass, as well as having the volume control for my sub up front. I imagine sound deading your boot would do a lot to keep the bass "in cabin", (warning off topic) which is something i will doing soon, as my next upgrade is a set of Hertz Mille MLK2 up front, move my CDTs to the parcel shelf and run the 4 speakers off a 4 Channel Amp, looking at the Audison Vrx 4.300. Also wouldnt a 12in sub be able to still move more air at a lower volume?

cheers

Evil

34Boostin Newbie

34Boostin

Posted
Posted

Basically the Short answer is this...........

Go for what ever sounds best to you. No-one can tell YOU what sounds good to YOU.

If you like the Punch from 2 10in Subs then go for that, Or if you think that 12's sound sweeter then that's what you want.

Personally I have always prefered the Low Rumble from a 15in, but that may have to go by the wayside when I finally get my 34 (Space may not allow it).

The general rule of thumb is the smaller the speaker, the quicker it can react to signals.

The Choice also depends on the type of music you will listen to.

Hopefully this may have given you something to mull over.

If all else fails, Seek help from a Professional.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...