Jump to content
SAU Community

Recommended Posts

Hi guys,

Pretty much im running these mods on my r32 gtst:

high flowed turbo

full hks xuast

pod

and boosts up to around 11psi.

just feel like its down on power and could have more potential.

Not looking at spending too much for a tune, but something decent.

Anywhere around south east qld / gold coast would be great.

Cheers

Tone

it is worth remapping the standard ECU if your not going to do any more mods... so i'd suggest getting a front mount before you got it remapped, cause otherwise later down the track u'll need to remap it again.

a SAFC is a piggy back computer that modifies the reported voltage from the air flow meter. its good for some tweaking, but if you want to take full advantage of that high flow, either an aftermarket ecu or a remap is in order.

yeah would have the standard ECU.

Is it not worth while remapping the standard computer or ?

whats safc?

in that case, Mercury Motorsport and DrDrift are the only 2 i know of who have the facilities to remap the stock ecu.

yes, if you increase the boost it changes the tune. do you have a boost controller at the moment ? if not, i would get an EBC and give mercury a call. they'll set whatever boost you want and remap to suit. Also, if your gonna be putting out more power, make sure your fuel pump is up to scratch.

fyi i think a remap comes in at about $500

as the others have said the safc is a piggy back computer, it wont give you the same tune a a remap, however i dont think the total would cost as much, in saying that if you have the $$$ get the ecu re-mapped it is worth the extra dollars in the end

stuff it if ur gonna run 12psi on the standard sucker ull be fine with the nissan ECU relearning itself and save ur money and buy a full ecu eg pfc.

but if ur doin massive increases eg new turbo injects afm NOS (lol) then u should check afr and tune accordingly.

go see the guys at 101 motor cafe. From my experience there are alot of bad tuners out there and i wouldnt recommend anywhere else

Edited by r_speedfreak_r

just trying to get an idea of things,

hopefully will be slotting in a new turbo/z32/injectors/pump in the next few weeks what would you expect to pay for someone decent to tune the car, it already got the usuals and powerfc

i know matt spry is awesome from the word of mouth but seemed quite expensive ($500 to do a tidy up tune on the car as it is[tuned by APC previously])

or is that the sort of price all tuners charge

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...