Jump to content
SAU Community

1997 R33 Series 2 Manual, Excellent Condition, *****$13990******

understated
 Share

Recommended Posts

understated Contributor

understated

Posted
Posted (edited)

LI-11-NE for sale

Description

Immaculate 1997 model with 85000 kms, first owner in australia, complied in october 2006

Serviced every 5000kms, mechanically A1

Paint and interior are both very clean and in good condition

Timing belt has recently been replaced

Custom Plates LI-11-NE included

Recently replaced air-con compressor and had air con system tested, all works perfectly

New tyres all round

Just had minor service done

Mods

Cat back exhaust

Turbo timer

Doors are sound deadened with dynamat extreme

Clarion head unit with amp and splits for the front, 6 inch speakers running off head unit in back

The car is currently being sold at National Car Connections on Paramatta Road, just outside the entry to the markets at Flemington. (Near Homebush, NSW)

The price is $13990 ono

Edited by understated
Link to comment
Share on other sites
understated Contributor

understated

Posted
  • Author
Posted
pics? and what colour, any mods?

Its silver, the only mods are an NS Giiken cat back exhaust and a turbo timer. The doors have had dynamat installed, and the stereo consists of a clarion deck, 2 channel amp for splits in the front and 3 way coaxials in the rear. I'm waiting for some daylight to get some decent pics.

Link to comment
Share on other sites
anomaly Enthusiast

anomaly

Posted
Posted

very interested, main problem is im up in brissy, but its only a 10 hour drive. it will only cost me bout 200 in fuel there

i dunno its a long shot but its exactly wat im looking for.. as long as its pretty much stock, clean, unthrashed

pic me up pls [email protected]

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LjB123
      R34 Series 1 And 2 Front Reo Difference?

      By LjB123 · Posted

      Awesome to know. I have a Series 1, and When pulling my front bumper off for the first time i realised my reo/crash bar was a bit worse for wear, and was going to try pick up a better one soon just so i can replace it. Someone is selling a full series 2 front bar and brackets for a decent price, so was going to probably reuse my brackets and install the new second hand reo/crash bar. I also have a genuine Altia body kit to do up, spray and put on, and not sure if that will use the series 1 or series 2 brackets for the front bumper, so having both will be handy, and knowing i can drill holes out to make stuff fit between series is also handy to know!
    • Kinkstaah
      R34 Series 1 And 2 Front Reo Difference?

      By Kinkstaah · Posted

      I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work. The center headlight brackets however, cannot. This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different. So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.
    • dbm7
      forum.r31skylineclub.com down or gone?

      By dbm7 · Posted

      Indeed  😃  Appears the site is back up now (migrated not updated) - kudos @funkymonkey & @PranK
    • GTSBoy
      rb20de neo +t conversion - boost pressure sensor needed?

      By GTSBoy · Posted

      If this, then this You can't really get away without it. There are hacks that you can do in Nistune, but things are much easier with the sensor than without it. If you're not planning to Nistune the ECU, then stop right now and add it to your plan anyway, because the ECU is going to shit the bed over the missing ABS and TC computers that it expects to see, and you need Nistune to stop it chucking all its toys over the side of the crib.
    • kindaruined
      rb20de neo +t conversion - boost pressure sensor needed?

      By kindaruined · Posted

      hey guys, so ive done a complete +t conversion using mostly stock parts on my rb20de neo r34.  Im wanting to know if a boost pressure sensor is needed? Seems like the engine cuts out when i try to do a pull and I have a feeling its because a boost pressure sensor is missing. I'm using a stock r34 rb25det neo ecu.
×
×
  • Create New...