Jump to content
SAU Community

Recommended Posts

could someone find part# for R34 GTT (ER34) ..namely the nissan water temperature sensor that sits under the rocker cover just up on the left from the radiator (near the top left hose)

sensor that fit's more or less directly in to the top hose housing No. 22630-44B20

Looking for the part number for the water pump on a R34 RB25DE Neo

I mainly want to know if its the same pump used in my engine as in a 33 RB25DE(T)

water pump numbers are not the same

R33 RB25DET No. 21010-21U26

R34 RD25DE No. 21010-5L327

hey mate sorry to post again but any luck on the weathershields? I'm trying to find these but for a 32 4dr however Nissan parts haven't been able to help :laugh:

600x450-2006100600001.jpg

600x450-2006100600002.jpg

i am sorry man i don't have any info on R32 accessory's. But the part No. for them weather shields is G3610-04U01. but i can't tell u if they would suit a 4DR. sorry

anyone can help me? its an ER34:

- RB25det Nissan OEM Main stud

- RB25det Nissan OEM Head stud

- RB25det Nissan OEM Piston Rings (86mm)

basically all the rebuilding parts except gasket kit.

thanks.

Looking for the rear seat cup holder, goes in the centre console between the drivers and passengers seats, can get vin if they differ due to interior trim colour.cheers

To suit a 5/2000 R34 gtt

Edited by EJD001
Looking for the rear seat cup holder, goes in the centre console between the drivers and passengers seats, can get vin if they differ due to interior trim colour.cheers

To suit a 5/2000 R34 gtt

two type depending on trim colour.

trim code K and W = No. 96965-AA000

trim code G (BLACK) = No. 96965-AA001

Hey Mate

could you please provide the codes for the following :happy:

i tried contacting nissan and they ask for the codes/ vin number, and i dont have a gtr lol...

Reason why im asking about the HCR32 GTR bar is because my friend had a N1 bumper on his Gtst and it fit up like Factory

with the standard front guards :thumbsup:

So was curious if they made a GTR bar to suit Gtst's width...

COLOUR: Spark silver Metallic- KLOG1

PARTS

1. Nissan HCR32 GTR front bumper code?

2. Nissan BNR32 GTR front bumper code?

3. Nissan BNR32 GTR N1 Version Bumper code?

4. Nissan BNR32 GTR front lower lip code?

Your help is much appreciated if you can :D

thanks! :D

Edited by drftps13=D
2001 R34 GTT RB25DET NEO

After part numbers for

Manual flywheel bolts

fan/drive belts

spigot bush

thermostat

oil filter

Thanks

Flywheel Bolts 12315-42L11

P/S Belt 11720-V7300

A/C Belt 11720-77A01

Fan & Alt Belt 11720-AA001

Spigot Bush 32202-B950A

Thermostat 21200-V7206

Oil Filter 15208-53J0A

Hey Mate

could you please provide the codes for the following :)

i tried contacting nissan and they ask for the codes/ vin number, and i dont have a gtr lol...

Reason why im asking about the HCR32 GTR bar is because my friend had a N1 bumper on his Gtst and it fit up like Factory

with the standard front guards :banana:

So was curious if they made a GTR bar to suit Gtst's width...

COLOUR: Spark silver Metallic- KLOG1

PARTS

1. Nissan HCR32 GTR front bumper code?

2. Nissan BNR32 GTR front bumper code?

3. Nissan BNR32 GTR N1 Version Bumper code?

4. Nissan BNR32 GTR front lower lip code?

Your help is much appreciated if you can :)

thanks! :cool:

As far as I'm aware, Nissan never made a GTR bumper to fit a GTST.

Could someone with FAST please lookup the Nissan part code for the Clutch Master Cylinder and Slave Cylinder from a 94 series 1 R33 GTST

I found this one earlier in the thread for the master cylinder but am unsure if there was a change to the clutch when they changed from series 1 to series 2

Right-o! The year and RB25DET made it a lot easier. I hope this is right. Gasket Set: 10101-17U27-

The Clutch Master Cylinder for the same year car is 30610-21U91-

Hope these help. Ron

Edited by TiTAN

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
×
×
  • Create New...