Jump to content
SAU Community

Recommended Posts

Hi all,

As per my EOI Thread, here is the cruise.

Meet Spot: PM will be sent out on Thursday June 28 (eastern suburbs)

Time: Meet 12:30 for 1:00pm depart

Where too: Heading out of the metro area. Total cruise length is around 120km, so a good 1/2 to 3/4 tank of fuel required.

Also, this is a cruise. it is NOT a hills run/midnight run/boy racer run.

The pace should be fun but not fast. I have heard of too many crashes and dickhead actions on cruises of late.

This is to get together to meet up with fellow SAU members and have a nice drive together.

To reitterate: Speeding & Dickhead behavoiur will not be tollerated. If you want to do this, go on a ns.com cruise.

Please also note that anyone who see's others doing innapropriate burnouts at the meet points, tailgating continuously, drifting etc, please report the numberplates to me and they will be reported to the authorities.

Finally, the route has been drawn up, but I wont have a chance to run it before hand. So notes are off the best I can do from memory :P

So post your name here for PM next thursday :(

Lee

Edited by Hotwire
Link to comment
https://www.sau.com.au/forums/topic/173315-sau-sunday-cruise/
Share on other sites

  • Replies 311
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...