Jump to content
SAU Community

Recommended Posts

As the CAMS delegate for SAU-VIC I get regular emails from CAMS. (Confederation of Australian Motor Sport) www.cams.com.au

Some of these e-mails may be of benefit to someone, most of them will concern few.

I'll post up in thread any information regarding CAMS emails.

Link to comment
https://www.sau.com.au/forums/topic/173560-cams-updates/
Share on other sites

It would be nice if SAU VIC had some CAMS trained officials, then we could start to look at running more of our own motorsport events. Such as Track for Dummy's

If you are interested in becoming a CAMS official get in touch with Bruce Carter from CAMS.

Email below:

Dear Club Members,

Please be reminded that a Scrutiny Module is to be conducted on July 7th

and 8th as posted on the Website. The course is to be held at the Jaguar

Car Club in Springvale. Further details will be forwarded to course

participants.

As it is not possible to conduct these complex courses on a regular

basis and there is no guarantee there will be another this year, could

you please ensure that this information is circulated amongst your

members as quickly as possible and ensure interested parties contact the

writer as soon as possible.

Kind regards

Bruce Carter

Confederation of Australian Motor Sport

State Office Victoria

Link to comment
https://www.sau.com.au/forums/topic/173560-cams-updates/#findComment-3189415
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...