Jump to content
SAU Community

Recommended Posts

ok.

got a 33 and im about 4k away from a 100k service. so im going to buy a gates belt. sweet!

just curious about some figures about getting it done at a workshop? how much roughly??

i looked at the DIY thread and it seems a little much for me to tackle, plus i want to make sure its done right. :O just

looking at getting the belt installed, thats it.

cheers

Link to comment
https://www.sau.com.au/forums/topic/173745-timing-belt/
Share on other sites

ok.

got a 33 and im about 4k away from a 100k service. so im going to buy a gates belt. sweet!

just curious about some figures about getting it done at a workshop? how much roughly??

i looked at the DIY thread and it seems a little much for me to tackle, plus i want to make sure its done right. :O just

looking at getting the belt installed, thats it.

cheers

It shouldn't cost to much... i just did mine myself and it wasn't hard at all... mines a Gates racing belt very nice...

Link to comment
https://www.sau.com.au/forums/topic/173745-timing-belt/#findComment-3191856
Share on other sites

looking at about $250 to $300 to fit (at $90/hr). about $120 to buy the belt. get them to look at your water pump to, if a bit iffy then get it replaced to. had mine done about 2 months ago. cost me $550 including fitting a fuel pump and dyno'ing the safc2. gates belts can be a bit noisey by the way

Link to comment
https://www.sau.com.au/forums/topic/173745-timing-belt/#findComment-3192000
Share on other sites

haha water pumps on its last legs..( coolant drips every second after a decent drive) im adding coolant in daily, just got to wait till exams are over then can get it all fixed.

im on 95k.. haha there not wrong when they say these cars should have timing belts water pump ect.. done at 100k.

cheers for the help

Link to comment
https://www.sau.com.au/forums/topic/173745-timing-belt/#findComment-3194332
Share on other sites

I wouldnt be too hung up about what your odometer says, there are 2 cetainties about all jap imports, they are from Japan and the speedo has been wound back. Unless you bought it in Japan yourself chances are its done well over 100k. I bought mine at 42k, with a non factory timing belt, go figure, Ive go no idea how many mine has done.

Link to comment
https://www.sau.com.au/forums/topic/173745-timing-belt/#findComment-3194373
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...