Jump to content
SAU Community

Recommended Posts

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 2 weeks later...
  • 4 weeks later...

still some to finish off

needs the following :

cut out to clear the fuse box mount

billet alloy filler cap

holes for the washer pumps

-10 fittings for the breather hoses

drain plug for catch can side

finish fillet welding the 2 bits together (amps needed keep throwing the breaker lol)

figure out what kind of outlet is required - either for filter or plumb back

looks good chris. making one up myself at the moment, how thick was the aluminium you used and what type of aluminium was it? Does it make much of a difference when it comes to welding if your using a soft or hard ally?

looks good chris. making one up myself at the moment, how thick was the aluminium you used and what type of aluminium was it? Does it make much of a difference when it comes to welding if your using a soft or hard ally?

This is 2.5mm alloy using 1.6mm filler rods

i am not sure on the grade of filler at this point or the alloy grade for the sheets- i just get off cuts and run some test welds to work out the best Amps for that alloy im using.

its just a shame the TIG im using does have a foot controller.

yeah fair enough - first posts one was without filler

going to make a couple more and get them welded up without filler

the one above i'll get the fittings and filler welded on - this one would be fine for powdercoat as that neatens up the welds heaps.

you're doing good stuff man.

I might be interested in 1 of the split washer bottle/catch cans actually...probably just in the raw metal finish...any chance of PM'ing me with a rough price?

let me finish this one off and then i'll let you know

would be different if using another dash fitting for legal plumb back versus getting a filter for it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...