Jump to content
SAU Community

R33 Skyline Sold!

tuitahi
 Share

Recommended Posts

tuitahi Community Regular

tuitahi

Posted
  • Author
Posted

^^Thanks Billy!!^^

I added some pics I took on my phone.

Over all the car is very straight, it only has one tiny dint on the driver's door.

I had one incident in the car ~4 months ago which resulted in panel damage down the passenger side after a stupid lady side swiped me. There was absolutely no stuctural damage and the car was repaired at Lansvale smash with all new panels (guard, door, sil, skirt, rear quarter) from Nissan Japan along with a full strip and respray of the bonnet. It was an awesome job and insurance forked out close to $8k! and the car is looking better than ever.

tuitahi Community Regular

tuitahi

Posted
  • Author
Posted
Hi tuitahi how are you?

If you dont mind could please up load dyno sheet pic?

Someone asked me how much my chip will make the car faster.

Hey Toshi, I'm good thanks!

I couldn't find the dyno sheet so I grabbed a screen capture from the SAU dyno comparison;

dynograph.jpg

weeman1 Collaborator

weeman1

Posted
Posted

hey everyone, im the fella that bought drew's car

its a great car im so happy with it, im starting to get the clutch under control lol.

thanx again mate all the best to ya

mitch

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...