Jump to content
SAU Community

Recommended Posts

Hey people, ive been doing alot of oil changes to my car in the past, and need to know how to correctly top it up....

I just bought a 5l castrol edge 0w40, and filter too, doing both at the same time....but need to know the best way to top it all up.

Usually i just loosen the filter, and the drain plug and let all the oil come out, then top it upin one hit....

but i was told to top up 4l first, then turn on car, then top rest up till the oil is at the high level on the dipstick....should i be topping up all 5l or no?

thanks in reply!

Put in about 4.5l. Start engine until the gauge registers pressure (5 - 10 secs), then switch off. Let stand for a few minutes to allow the oil to drain back to the sump. Now check dipstick, add oil as necessary.

drain the oil,

replace sump washer and torque plug up,

remove and replace filter,

fill engine with 4L or so of oil,

start engine, wait for oil light to extinquish,

let sit for a minute, check dip stick level.

top up until FULL.

the reason you start it after filling initially is because the oil filter is not full of oil initially until you start it and you will get a misleading oil level. (higher then it actually will be once new oil filter is full)

iv serviced cars many times... the way i see it and do it is,

get it warm (as warm oil will flow through internals easier than cold oil),

you get her up?,

undo plug and filter, let drain over a period of time (i leave it for over an hour, but no need to do it as long),

make sure area is clean of dirt ect. by using a rag, put new filter on 2/3 turn (run a bead of clear oil over rubber gasket helps seal under heat),

clean around plug hole on sump, put plug back in,

lower the car down,

put new oil in (i put in same amount that comes out), let sit for a bit, check dip stick and slowly top up bit by bit waiting about 1 min in between check until level is close to high level on dipstick,

take for a short drive to get oil a bit warm then recheck because new oil will be pushed around all internals, turbo ect. recheck and do slight top up done... and done right

* be sure to check your filter after car has been driven ( after a decent drive) for minor leakage. if leaking just tighten it a bit with your hand. (dont leave it to long to check and tighten as heat will make rubber gasket go hard and will break seal and then you will have to replace filter again...)

* best to do it yourself in your own time because most mechanics (under a time scedule) wont let it sit to drain long enough, which leaves contaminated oil inside engine and will contaminate new oil.

If done correctly when driving (highway or freeway) your dash cluster oil pressure gauge should be on the 4 mark or very very close to.

any qustions please ask... cheers

Edited by 4drftn
  • 6 months later...

Ive heard a few people commenting that you should fill your filter full of oil before fitting.

Please people, this will only end up in a mess, esspecially on a skyline where the filter is at an arms reach.

Do not waste your time, Ive never heard of a filter "popping off" because of this.

yeah i wouldn't worry, it only takes a couple of seconds to get pressure, because the engine was already hot from when you drained it, there still should be a fair bit of oil hanging around on most components, and if you run an oil like motul with ester or royal purple with molyb, it tends to cling to the parts for a while anyway after shutdown, so you have some protection still even without pressure.

And make sure that the old oil filter seal isnt stuck on the engine when you change the filter, really makes a mess of your fire wall and leaves a hansell and gretel trail from your mates house where you did it all the way back to your house and then leaves the rest of the oil in a ig puddle on your drive way...... errrr .... so im told :D

Ive heard a few people commenting that you should fill your filter full of oil before fitting.

Please people, this will only end up in a mess, esspecially on a skyline where the filter is at an arms reach.

Do not waste your time, Ive never heard of a filter "popping off" because of this.

i put put abit of oil in and swish it around before installing. works for me. whether it does anything i dunno..ha

  • 2 weeks later...

Dont bother putting any oil into the filter before installing it. It does nothing except make a mess. However, you do need to place grease or oil around the seal to help it stick. Also, when you drain say 4.9L of 5L of oil, 100mL in the engine wont make much difference. Plus, do you guys change your sump plug washer everytime you change your oil? Otherwise it will leak. If you know exactly how much oil goes into the car, pour it all in. Then run the car until the oil light goes out, wait another 10 seconds then turn the car off and check the oil. There is no need for huge drives, just enough to pump oil around the engine. If the oil mark in a few millimetres from the "Full" position on the dipstick, leave it. The oil will drain back into the sump and fill that up. While you are draining the oil, go though and check the underside of your car as well. Steering boots, oil leaks, CV boots, fuel filter, that sort of thing. Once you have gone through and checked all that, then the oil will have finished draining. Don't bother about waiting for every tiny drop to come out, there will always be some left in there. Dont worry about contaminated oil too much though, that is what an oil filter is there for!!

And finally, DO NOT FORGET TO TIGHTEN THE SUMP PLUG!!!! A hand tightend sump plug will not leak straigt away, but within a few kms it will fall out and its goodbye oil, goodbye motor, big, big trouble! That is the most important step of the whole procedure!

highway cruizing (100km/h in 5th or top) is the only way to check true oil pressure, oil pressure will not build up on idle. its not something you have to do straight away, but it gives you a good indication of the oil quality etc. currently in the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...