Jump to content
SAU Community

Recommended Posts

Hi,

Car: HCR32(Gts-t, RB20DET), Nomal Turbine&Fuel Pump&Injector

E-manage blue

Anyone here have a similar setup want to donate their Airflow Adjustment and Ignition Timing maps? I need to write a base map and having these on hand would be a great help.

Thanks.

Edited by GloriaShield
Link to comment
https://www.sau.com.au/forums/topic/175101-greddy-e-manage-map/
Share on other sites

i doubt anyone will be willing to post what they've paid $400-$600 for free. it might not be too safe either.

also, youve said you own an r34gtr, an r34 gtt and now an r32 gtst. i hope you're not going to distribute the map anyone gives you as your own.

i doubt anyone will be willing to post what they've paid $400-$600 for free. it might not be too safe either.

also, youve said you own an r34gtr, an r34 gtt and now an r32 gtst. i hope you're not going to distribute the map anyone gives you as your own.

Thanks for your advice. My vehicle is only BNR34 VSpec(GTT is sold). HCR32 is my friend's. We will try, refer to rb20det map of powerfc. Regards.

Edited by GloriaShield

but it is no use to anyone using an emange, because an emanage only alters the stock tuning. the pfc uses all new tuning. if you were to input those values into an emanage you would be extremely out of tune. for example in some areas you would be adjusting the timing by 30 degrees, not setting it to 30 degrees.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...