Jump to content
SAU Community

Recommended Posts

I am waiting to get to the end of our tank to see how the fuel consumption is going after my 1st service.

who knows a cleaner air filter and new oil and plugs etc could make a difference

I am really interested to hear of peoples opinions on wether or not the " equivalent " o2 sensors work as well as a genuine Nissan one. I dont really want to pay near on $250 for genuine

couldnt hurt hey?

oh and something else I noticed on the weekend.. when I was leafing thru my service manual

it actually says that the o2 sensor should be serviced/changed at 40 thousand and 80 thousand k

so .. I wonder how many imports have NEVER had it changed.

being that your not going to really notice it not working other than shitty fuel economy

If people are interested, i might just ring up and find the prices for OEM O2 sensors then.

i only fill up when the fuel light turns on...which that point i think theres only 10lt left.

so for the rest of the 55lt i only get around 280km but only boot it from time to time

no major mods but runnin really rich i reckon

For guys who are getting over 400+ km, I presume you are babying the car most of the time? I would be lucky to break into the 300km, guess that’s the down side when you drive your car once a fortnight.

Mind you, I do remember getting over 400+KM when the R34 was stock as a rock. The pod and exhaust threw the fuel figures out the window. Would love to see what happens once the turbo, cooler, injectors and pump gets done :())

For guys who are getting over 400+ km, I presume you are babying the car most of the time? I would be lucky to break into the 300km, guess that’s the down side when you drive your car once a fortnight.

Mind you, I do remember getting over 400+KM when the R34 was stock as a rock. The pod and exhaust threw the fuel figures out the window. Would love to see what happens once the turbo, cooler, injectors and pump gets done :D))

If it was me I wouldn't just be accepting this as normal.

Get your car dyno'd and check the Air Fuel Ratio graph. It should be somewhere around 11.5:1 at the lowest point. Any lower and its likely to be running too rich, which essentially means you're throwing fuel away, with no additional benefit.

If you dont have an SAFC or similar ecu to tune AFR's, then I'd suggest this be your next mod. It should cost you $400 all up for a 2nd hand one, including installation and tuning (depending on where u go). And while you're getting it dyno tuned, check your ignition timing at the same time.

Its all about getting your engine running as efficiently as possible, yet still safely. With a good tune you should be seeing improved fuel economy and it could pay itself off in 12 months or maybe earlier, depending on how often you drive. :)

I found with my car that even just an exhaust can push your AFR's down to 10 or even lower if you raise the boost. They run rich from the factory and adding more boost will likely make it add more fuel and run even richer. Even an exhaust can raise the boost level and end up using more fuel rather than less.

You should be able to easily achieve over 350-400km to a tank provided you dont drive around with your foot to the floor and dont ONLY do short trips (ie. with the engine running cold).

So to summarise, some things to do to lower fuel consumption are:

- get a free-flowing exhaust

- install a SAFC or similar ecu to tune AFR's.

- check ignition timing on a dyno

- use boost a little less (or not :( its what you bought the car for right?).

hope this helps. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...