Jump to content
SAU Community

F.s. Rb25 10sec Setup

CRNAGE
 Share

Recommended Posts

CRNAGE Apprentice

CRNAGE

Posted
Posted (edited)

The engine is out of my r33 gtst that went 10.5 @ 125mph a couple of months ago, new setup is being built so this stuff has got to go!

RB25 long motor, sump to rocker cover, has forged pistons, shot peened rods, prepped crank and block, ported head, genuine nissan head gasket, tomei 256degree poncams, tomei exhaust cam gear. this engine made 480rwhp with 24psi through a gt3540. runs perfect and comp tested perfect before being pulled out of the car. $5000 or very close offer!

polished plazmaman plenum, bolt's to standard runners, 600x300x75 intercooler with polished alloy pipes and turbosmart bov to suit the plazmaman plenum, incuded is the exhaust manifold to suit a gt3540 and a 38mm wastegate but no turbo and gate. plenum cooler with pipes and exhaust manifold $2450 or very close offer!

850cc sard injectors(side feed) with rail and sard reg $850 or very close offer!

apexi power fc and z32 afm with harness $1000 or close offer!

or the complete engine with all the above for $8500, all you need is a 3540 and a gate and you got a reliable 10 sec package!!!!!

Als raceglides built c4 auto, full roller bearing, all the good gear inside, deep pan, transbrake, 3500rpm converter and a b&m pro ratchet shifter and tailshaft for r33. $4200 or close offer! box is awsome and still usable on the street!

offers only by pm or you can call Alex on 0413 311 919.

Edited by CRNAGE
Link to comment
https://www.sau.com.au/forums/topic/176318-fs-rb25-10sec-setup/
Share on other sites
CRNAGE Apprentice

CRNAGE

Posted
  • Author
Posted
Hey mate. Do you have any more specs of the auto. What power was it built to handle??

what specs are you after? it will cop 800hp no prob, this box will go in the 9's!!!

spudsr33 Enthusiast

spudsr33

Posted
Posted (edited)

Where you located i want that power fc. Does it come with the hand controller and the wiring set up for a series1. P.M me asap........ P.S is his for a manuel

Edited by spudsr33
CRNAGE Apprentice

CRNAGE

Posted
  • Author
Posted
Where you located i want that power fc. Does it come with the hand controller and the wiring set up for a series1. P.M me asap........

sydney, no hand controller and yes its for series 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...