Jump to content
SAU Community

Recommended Posts

Sorry about first post stuffed up!.........First time user be gentle....I have a exhaust give to me when i purchased my stagea its a Tanabe Hyper Medalion. Was wondering if any of you out there have used

and any comments!..... And yes i did a search but i got no hits Thanks Shane

I recently just fitted a HKS HI POWER to my Stag and i reakon its a bloody good exhaust, the sound is fantastic no drone from inside the car at all, it is rather quiet when you are cruising around and on idle but when you give it a bit damn it sounds good.

Cheers Simon

oh my go bro easy as

i run the blitz Nur exsahust

sounds sweet as nice and quite enough to pass the db test.

to test yours put it on and get a db meter (J car supply a chepo that you can build yourself)

put the car on level ground on a flat area (not near a gutter) and hold the db meter 45deg to the exsaust 1 metre from the exsahust tip get some on to hold the car on 3000rpm under no load it shold read less than 89db (this is quite loud)

if it dosn't pass leave it who cares?

if you get pulled up and defected for it explaine your predicament to the local exsahust shop and they will be able to make a silencer for you to get the defect cleared and then you take it back out after it's cleared then keep the silencer for next time you get pulled up

I recently just fitted a HKS HI POWER to my Stag and i reakon its a bloody good exhaust, the sound is fantastic no drone from inside the car at all, it is rather quiet when you are cruising around and on idle but when you give it a bit damn it sounds good.

Cheers Simon

What was the total cost?

I have this exhaust. It is nice and quiet if that is what you like. I have fitted the dump/front pipe as well and there is a noticeable power gain to be had. i suspect a noisier exhaust may make more power. YOu should have no problem passing db tests and it is not so obvious that cops pull you over anyway. I dont know too much about other exhausts but i like this one.

why not just install the tanabe... if its for the stagea it should just bolt on.. its gonna be a lot cheaper than buying a new exhaust...

if you dont like it.. then look at buying something else....

I concur. If you've got the exhaust sitting there.....

QUOTE(FLYSLY @ 15 Jul 2007, 05:56 PM)

I recently just fitted a HKS HI POWER to my Stag and i reakon its a bloody good exhaust, the sound is fantastic no drone from inside the car at all, it is rather quiet when you are cruising around and on idle but when you give it a bit damn it sounds good.

Cheers Simon

What was the total cost?

A few questions about your exhaust FLYSLY:

1) Is it defiantely the HI POWER and not the HI POWER SILENT? does it have a proper middle muffler or just the hotdog/resonator thing? I was always afraid that the drone would be unbearable with the HI POWER.

2) How is the ground clearance? i have the whiteline/bilstein suspension kit (like many here) and with 335mm centre of wheel to guard (the top circlip) im having some exhaust clearance issues... and thats with the stock exhaust.

These are the things that have been holding me back from getting the HI POWER. If you could ease my mind I would be very appreciative.

I think that you have to try it to know..... if you don't you'll always be wondering.

Mine came with Fujisubo, I love the way it sounds, not too loud, (cept when it backfires at gear changes, then it sounds reeellly cool. :P

A few questions about your exhaust FLYSLY:

1) Is it defiantely the HI POWER and not the HI POWER SILENT? does it have a proper middle muffler or just the hotdog/resonator thing? I was always afraid that the drone would be unbearable with the HI POWER.

2) How is the ground clearance? i have the whiteline/bilstein suspension kit (like many here) and with 335mm centre of wheel to guard (the top circlip) im having some exhaust clearance issues... and thats with the stock exhaust.

These are the things that have been holding me back from getting the HI POWER. If you could ease my mind I would be very appreciative.

It is definately the HI Power, yes it does have a proper middle muffler, which i thought was quite strange because according to the picture it is supposed to just have a hotdog resonator type thing.

Umm the clearance is pretty good, my car is also lowered it does sit a bit lower than i would have liked at the rear muffler but i plan on taking it down to the exhaust shop to have it lifted a bit not becuase it hits anything when i driving or going over speed bumps or anything but just cause it looks a bit silly cause its not snug under the rear bar.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...