Jump to content
SAU Community

Recommended Posts

I'm the same mate. Between my Plazmaman plenum, ETM manifold, numerous other custom alloy and stainless gear I've had done, and an all signing and dancing $20k welder we've recently ordered in at work... I also have one hell of an appreciation of professional welding skills!

Leigh's welding abilities are in another dimension in comparison to my capabilities.

  • Replies 843
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Good and bad. It wasn't bad as far as first meetings go and considering the number of new things to keep track of and the tame settings in the thing, it didn't do too bad at all.

First run out I blew the manifold to BOV line clean off and discovered that the spring in the BOV is about 16.5-17psi. :D It was doing all the boost control for me :) and we pulled every cooler pipe, hose, clamp and fitting off to chase the boost leak that was none of the above.

With that problem sorted (but with round 2 and 3 qualifiers happening in my absence, I had to make do with a random dial-in for first round eliminations. I thought that an 11.anything would do for the day and so dialed in 12.00. It would only hold about 3psi on the foot brake so it drove off the line again (2.006 60') and with the boost leak fixed went 11.87 @ 120.89mph. The speed was back but the launch was atrocious. The transbrake would have to do for grudge runs soon to come.

I forgot to arm the brake for the next pass so we just wont talk about that, okay? :P

Last pass they had time for was ok. Good burnout, everything ready to go, transbrake to about 8psi and when i let go of the button it just went sideways and spun all through first with me peddling it to get it under control. I should have in-car vid of this pass soon. Slow (11.7 @ 120 - 1.9 60').

That was all we had time for today but will be back soon to revise the launch technique. A 1.60 60' time will see the car in the bottom 11's/high 10's no trouble at the same boost etc. Fingers crossed. :)

Good to catch up with a few people today. Thanks to Elmsy, Macka and Yavuz from Unigroup Engineering for their help.

did u take any data logs? if so what did the oil pressure one look like? (i'm using the same pump/line setup as u on a car i'm building)

Oil pressure was about 60psi when oil up to proper operating temp. That's reading the gauge during the run. Haven't seen logs yet.

One of the best parts of the day was cruising with this guy. Car runs 8.30's on slicks and went 8.60's on radials. Made the 45km cruise and drove through the night from Calder Park to be at the event. (They raced the day before!)

24ndv88.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...